Mirolin BAIN-TOURBILLON EN ACRYLIQUE Directives D'installation Et Manuel Du Propriétaire page 9

Safe zone
Figure 8 - Exclusion Zone, Side view
Minimum height for NEMA plug as shown in fig. 8 is 38
!
mm in the standard,
recommended safe zone height is 305 mm ( 12").
Receptacle shall be installed outside the exclusion
!
zone.
Receptacle should have a spray cover If there is no
!
exclusion zone.
Supply connection power supply cord shall be three
!
conductor, size 14 AWG and provided with an
attachment plug cap rated 15A 125V.
IMPORTANT SAFETY INSTRUCTIONS.
READ, FOLLOW AND SAVE THESE INSTRUCTIONS
1. Warning: risk of accidental injury or drowning:
children should not use whirlpool bathtub without
adult supervision;
2. Warning: risk of accidental injury or drowning:
do not use whirlpool bathtub unless all suction
guards are installed to prevent body and hair
entrapment;
3. Warning: to avoid injury, exercise care when entering
or exiting the whirlpool bathtub;
4. Warning: risk of electric shock:
electric appliances (such as a hair dryer, lamp,
telephone, radio or television) within 1.5 m (5 ft.) of this
whirlpool bathtub;
5. Caution: test the ground fault circuit interrupter,
(GFCI) protecting this appliance periodically in
accordance with the manufacturer's instructions;
6. Warning: risk of hyperthermia and possible
drowning: water temperature in excess of
40º C (104º F) may be hazardous to your health.
Check and adjust water temperature before use.
7. Warning: keep hair and clothing a minimum of twelve
inches away from all suction fittings and drains at all
times. Persons with long hair should either secure hair
to a minimum length or wear a bathing cap.
Safe use of a whirlpool bath
Your physiological response to a whirlpool bath depends on
your age, health and medical history. Initially, stay in the bath
for a short time only until you learn your tolerance for hot water.
If you develop a headache or become dizzy or nauseous, get
out at once and cool off under a shower. Get medical help if
symptoms persist.
Consult your doctor before you use the whirlpool for physical
therapy of an injury or disorder. Don't take a whirlpool bath
without your doctor's consent if you are ill or pregnant, or if you
but Mirolin industries
do not permit
suffer from high blood pressure, heart disease, or other
health problems. Never take a whirlpool bath while under
the influence of medication, drugs, or alcohol.
Warning
Do not run the whirlpool pump unless the bath is filled with
water to a level of 2" (50 mm) above the whirlpool fittings.
Use only small amount of soap or other bath preparation in
whirlpool baths. Otherwise, excessive foaming may occur.
Suction
Do not block suction inlet screen on whirlpool baths. Water
is circulated back to the pump from this location. Should
the inlet screen become blocked in any way the safety
suction will engage and the pump will start cavitation. The
pump will immediately shut down stopping the flow, thus
releasing whatever is blocking the screen. When the
screen is free of blockage, the pump will automatically start
up and the system is back to normal. Under no
circumstance is the pump to be used without the screen on
the suction return.
OPERATING INSTRUCTIONS
Air Switch
Press the tub mounted air switch to start the pump. The
pump will run continuously. Press the Air Switch (A/S)
again to stop.
Whirlpool Fittings
Use a finger to swivel the whirlpool jet to give the direction
of flow required. Do not plug the whirlpool fittings while the
pump is running.
The flow of water can also be increased by turning the jet
face plate clockwise and decreased by turning
counterclockwise. Refer to Figure 9.
Caution: The whirlpool jets can be misadjusted to
throw a stream of water out of the tub, onto the floor.
Drain the Bath
Check that the pump is not running. Drain the whirlpool
bath after each use. It is not a spa that can retain its water
for repeated use through continuous filtration, heating and
chemical treatment.
Motor Protection
The blower and pump motors are equipped with a built-in
thermal overload protector to shut off the motor in the
event the temperature becomes excessive (as a result of
mechanical or electrical problems; such as low voltage,
poor ventilation, overload lines, etc.). The motor will restart
automatically as it cools down.
FIGURE 9 - ADJUSTABLE FLOW WHIRLPOOL JET
3