Suntec Wellness KLIMATRONIC COMFORT 7.0 Eco R290 APP Mode D'emploi page 18

Functions
1. Switch On and Off
- Please press the On / Off button (1) to turn on the unit.
- Please press the Mode button (4) on the control panel to select the desired mode.
- Alternatively, you can select any mode using the buttons on the remote control shown above.
- Please press the On / Off button (1) again to turn off the unit.
2. Functions
- The device has three functions: Cooling, ventilation and dehumidification. For night operation, we
recommend that you operate the unit in sleep mode.
2.1 Cooling Mode
- Please press the Mode button repeatedly until the "Cool" indicator lights up.
- Press the up/down button to set the temperature. The temperature can be set between 16℃ and 30℃.
- Please press the Fan Speed button (2) repeatedly to select between high and low fan speed. The
corresponding indicator (high/ low) lights up.
2.2 Fan Mode
- Please press the Mode button repeatedly until the "Fan" indicator lights up.
In ventilation mode, the room air is circulated but not cooled.
- Please press the Fan Speed button to select high or low speed. No temperature can be selected in
this mode.
2.3 Dehumidification Mode
- Press the Mode button on the control panel or remote control until the "Dry" indicator lights up. The fan
speed cannot be selected. The user should connect the drainage hose to the drain at the bottom of the
unit.
- When the ambient temperature is higher than 16°, the compressor switches on automatically. As soon
as the ambient temperature drops below 16°, the compressor stops automatically. To protect the
compressor, it continues to run for approx. 3 minutes until it stops completely.
- As soon as the water tank is full, a beep sounds, the display shows "FL" and the Full indicator lights
up. Please then follow the steps below under 'Emptying the water tank'.
Note: In this mode, the fan speed switches to Low and cannot be set.
3. TIMER 1h-24h:
When the unit is switched on, press the Timer button (5) first. Now you can set the desired switch-off
time with the up/down buttons.
When the unit is switched off, press the Timer button (5) to set the switch-on time.
4. Sleep mode:
Please press the Timer button (5) and the Up button (3) at the same time to switch on the sleep mode.
This mode can only be set when the unit is in cooling mode. Please use the up/down buttons (3) to
select the desired temperature. The unit will operate at low fan speed and the selected temperature.
After 2 hours, the unit will automatically increase the temperature by one degree, and again by one
degree after another 2 hours. Press the Mode button (4) to exit the sleep mode or use the on/off button
to switch off the unit.
Connection to the Wifi and the Suntec Wellness APP
• Please download the "SUNTEC Wellness" app from the App Store or Google Play and install it.
• Please create a user account after the installation.
• Please activate the Bluetooth access in the settings of your mobile device.
• Please connect the device to the power and press and hold the fan speed button (2) until you hear a
beep and the "WiFi" indicator (7) flashes slowly. Please press and hold the fan speed button (2) again
until you hear a signal tone.
• Please follow the steps below in the app as soon as the indicator flashes:
Please select "Add device".
•
Please select under the category "large household appliances", "portable air conditioner" and
•
then follow the instructions on your mobile phone screen.
• As soon as the device is successfully connected, the WiFi indicator lights up constantly.
• The device works with the most popular voice assistants from Amazon and Google.
In order to use the voice function of Amazon or Google, it is necessary to couple the device once with
•
the "SUNTEC Wellness" app. All further steps are displayed in the app.
To remove the device from the Wifi, please press and hold the fan speed button (2) again.
•
If you have any further questions about the app, please visit our web page at:
•
www.suntec- wellness.de/suntec-app/