Skytec 170.630 Mode D'emploi page 11

By turning back and forth the control knob with the CD playing, "drawling" effects can be created.
Return to a desired spot
1) While playing a title, switch to pause with the button ►II if the spot is reached to which the unit is to return later. The buttons
►II and CUE flash.
2) If required, the spot can be selected more precisely with the control knob REV/ FWD. The current spot can be heard
continuously.
3) Shortly press the button CUE. Thus, the spot is internally marked. (If the current spot can be heard, press the button CUE
again shortly for muting.) The button CUE now lights continuously. The button ►II continues to flash as a request to start the
replay.
4) Start the replay again with the button ►II .
Caution: Do not press the button I◄ or ►I , otherwise you will delete the marked spot.
5) It is possible to return to the marked spot with the button CUE. The player mechanism is then set to pause.
6) Start the replay with the button ►II or press the button CUE again and keep it pressed. After releasing the button CUE, the
player mechanism is set to pause on the marked spot. By keeping the button CUE pressed again, it is possible to repeat the
replay from the marked spot on as many times as desired.
Note: In the operating modes "Single" and "Single Relay" it is possible to return to a desired spot within a title only.
Changing the speed and the pitch
To change the speed and thus the pitch (±16 %), press the button PITCH. The LED next to the button PITCH lights up and the
speed can now be changed with the PITCH CONTROL. The display shows the percentage deviation (j) from the standard speed
adjusted with the slider control. The speed can be changed in steps of 0.1 % in the range of 0 % to 6 % and in steps of 0.2 % in
the range of 6 % to 16 %.
The button PITCH switches from the speed adjusted with the slider control to the standard speed and vice versa.
Matching the beat between two music pieces
With the buttons PITCH BEND, the beat of a title in player mechanism 1 can be matched to a title in player mechanism 2 or vice
versa.
1) Activate the PITCH CONTROL with the button PITCH. The LED next to the button must light up.
2) Use the PITCH CONTROL to match the speed of the currently playing music piece to the speed of the second music piece.
3) Synchronize the beats of the two music pieces with the buttons PITCH BEND: As long as the button + or - is kept pressed,
the title is played 16 % faster or slower than the standard speed, and the LED of the button PITCH and the speed display (j)
flash.
Note: The button PITCH BEND + is ineffective at a speed of +16 % adjusted with the PITCH CONTROL, and the button - is ineffective at a
speed of -16 %.
Controlling start/ pause via the crossfader
The two player mechanisms of the CD player can be switched alternatively from pause to start and vice versa via the
crossfader. For this purpose, slide the two sliding switches X-FADER START to the left to position ON and set the two input
selector switches to the position CD. If the crossfader is now slid to the left stop, player mechanism 1 starts and player
mechanism 2 is set to pause. As soon as the crossfader is slid to the right stop, player mechanism 1 is set to pause and player
mechanism 2 starts.
The pre-fader listening facility via headphones allows pre-fader listening of a title on the player mechanism set to pause:
1) Go to the desired title with the buttons I◄ and ►I
2) Keep the button CUE pressed. The title plays as long as the button is pressed.
3) After releasing the button CUE, the unit returns to the title beginning. To start the title, slide the crossfader to the other side.
Note: Control via the crossfader is rather pointless in the operating modes "Single Relay" and "Continue Relay" as the replay
automatically changes to the other player mechanism at the end of a title or at the end of the CD.
Do not switch off the power when the disk holder is open
SPECIFICATIONS
INPUT SENSITIVITY
Mic DJ 3 mV / 1 K Ohm
Phono 3 mV / 47 K Ohm (RIAA)
Line 150 mV / 100 K Ohm
Headphone Output 400 mV 8 Ohm
OUTPUT LEVEL
Master 0dB 775 mV 600 Ohm
Booth 0dB 775 mV 600 Ohm
INPUT POST
Common Jack (DJ Mic) x 1.1/4" TRS
Jack Mic x 2 RCA (Line/Phono/CD) x 6 pairs
OUTPUT POST
¼" TRS Jack (Mic) x 2 RCA (Master/Booth) x 2 pairs
SOUND EFFECT
WARNING
GENERAL
Bass
Mid
Treble
Low Cut
Mid Cut
High Cut
Mic Medium
Auto Talk-over
THD+N
Signal to Noise Ratio
Frequency Response
DIMENSIONS
11
± 15 dB 100Hz
± 15 dB 1 kHz
± 15 dB 10 kHz
-25 dB
-25 dB
-25 dB
+3 dB
14 dB
0.02% Rated Output
Better than 80 dB
20 Hz-20 kHz ± 2 dB (RIAA ± 2 dB)
Control Unit 482 (W) x 222 (H) x 130 (D)
Main Unit 482 (W) x 88.5 (H) x 260 (D)