T.I.P. MTS 30000 UV25 Mode D'emploi page 13

9. Push the rear bearing support (4.5) including the axial bearing washer (4.3) out of the pump; you may find a
pen to be helpful to accomplish this.
10. Insert this pen in the small bore at the pump's rear side (8) and use it in order to push the rear bearing
support (4.5) including the axial bearing washer (4.3) out of the pump.
11. Clean all components - please use clear water only - so that they allow to be easily moved. Do not use
sharp-edged objects.
12. Proceed as follows in order to reassemble the pump:
12.1. Put the rear bearing support (4.5) including the axial bearing washer (4.3) onto the axle (4.2) and
insert it in the pump (8).
12.2. Put the rotor (4.1) onto the axle (4.2). Caution! The rotor (4.1) has a very strong magnetic field,
which will pull the rotor into the pump (8)!
12.3. Put the front bearing support (4.4) including the axial bearing washer (4.3) onto the axle (4.2).
12.4. Insert the inlet lid (3) in the pump (8), holding it in the same position as when you took it out of it, then
turn it clockwise until it stops.
12.5. Insert the front (1) and rear (6) filter covers in the pump (8).
To ensure proper functioning, repeat the above procedure frequently, depending on clogging and working time.
Maintenance
In order to prolong the service life of your pump and to keep it in good operating condition, it is recommended
to carry out maintenance and cleanup regularly.
This can be done by everyone, quickly and easily. See „Dismantling / Assembly".
Servicing intervals
- In the beginning check performance of your pump every day. If necessary, clean the filters.
- Since servicing intervals (complete cleanup) will vary depending on pond pollution, repeat the periodic
service to your pump in accordance with the requirements given.
Should you determine that there are damaged or worn parts, do replace them. See „Spare parts".
Winter / Pump care
Protect your pump from freezing!
Take the pump out of your pond in autumn.
Clean the pump completely following the outlined instructions.
During the winter months store the pump in a frost-resistant room.
Spare parts
For ordering spare parts, please indicate the pump type, the designation and the Art.-No. as per table below
(see also fig. 5 + 6).
Item Designation Pump Type
1 Filter cover front WP 1300 S
WP 2500 S, WP 3300 S
3 Lid incl. sealing ring WP 1300 S
WP 2500 S, WP 3300 S
4 Rotor complete WP 1300 S
WP 2500 S
WP 3300 S
6 Filter cover back WP 1300 S
WP 2500 S, WP 3300 S
7 Handle/Stand WP 1300 S
WP 2500 S, WP 3300 S
PLEASE PLACE YOUR ORDER IN WRITING AND SEND IT TO THE FOLLOWING ADDRESS OR CONTACT YOUR
DEALER DIRECT!
T.I.P. - SERVICE
Siemensstraße 17 · D - 74915 Waibstadt · FAX +49 72 63 / 91 25 85 · service@tip-pumpen.de
Art-No.
104/002708
104/002752
168/009073
168/009110
168/009068
168/009111
168/009112
104/002710
104/002753
104/002711
104/002754
24
Conditions of Warranty
This device was produced and tested with the most up-to-date methods. In accordance with the legal
conditions of each country in which the device is sold, the seller ensures a faultless manufacturing guarantee
and the irreproachability of the materials. The warranty period begins on the day that the product is bought,
under the following conditions:
Defects which may be attributed to failures of production or materials will be corrected free- of- charge within
the warranty period. Complaints must be reported directly upon the discovery of a defect.
The warranty claims expire if the buyer or a third party attempts to manipulate the device. Damages due to
improper handling or use, incorrect placement or storage, improper connection or installation, abuse, or other
external forces do not fall under the provisions of guarantee. The parts subject to wear, for example the rotor,
filter materials, and light fixtures are not under warranty. All parts are produced with great care and the employ-
ment of high-quality materials: They are designed for a long life span. However, the wear is dependent upon the
way and intensity with which the product is used, and the maintenance intervals. For this reason, adherence to
the instillation and maintenance instructions ist essential to the long life span of all parts subject to wear.
In the case of a complaint, we reserve the right to repair or replace any faulty parts or to exchange the device.
Parts which have been exchanged become our property.
Damage claims are not possible, as far as they do not stem from intent or gross negligence of the manufacturer.
Further claims do not exist in connection with the warranty. Claims must be proven with the presentation of the
receipt. The warranty is valid in the country in which you originally purchase the product.
Instructions:
1. If your device does not function properly, please ensure that there are no other reasons to which the
problem may be attributed, for example, a cut in the energy supply oder incorrect handling.
2. In addition to the faulty device, please ensure that you have spent the following items: Receipt of purchase
and Description of the defects (an exact specification of the defect will facilitate a speedy repair).
3. In the case that the device needs to be repaired, please disconnect all attachments which do not belong to
the original accessories before you ship the device.
By warranty claims, malfunctions, and the need for replacement parts please turn to:
T.I.P. - SERVICE
Siemensstraße 17 · D - 74915 Waibstadt · FAX +49 72 63 / 91 25 85 · service@tip-pumpen.de
Only for EU countries
Do not dispose of electric tools together with household waste material!
In observance of European Directive 2012/19 EU on waste electrical and electronic equipment and its
implementation in accordance with national law, electric tools that have reached the end of their life must be
collected separatly andreturned to an environmentally compatible recycling facility.
25