Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
DVCT36CBP9(-1,-2)
This conversion kit is to be installed by an Empire Comfort Systems, Inc., distributor (or other
qualified agency¹)* in accordance with the manufacturer's instructions and all codes and
requirements of the authority having jurisdiction. Failure to follow instructions could result
in serious injury or property damage. The qualified agency performing this work assumes
responsibility for this conversion.
National Fuel Gas Code Z223.1 (Latest Edition)
1
*The term "qualified agency" means any individual, firm, corporation or company which either
in person or through a representative is engaged in and is responsible for (a) the installation
of gas piping or (b) the connection, installation repair, or servicing of equipment, who is
experienced in such work, familiar with all precautions required, and has complied with all the
requirements of the authority having jurisdiction.
Perform the safety shutdown test any time work is done on a gas system to avoid the possibility
of fire or explosion with property damage, personal injury or loss of life.
CHECK SAFETY SHUTDOWN SYSTEM
Intermittent Pilot System
1. Turn "OFF" using remote control. Main burner and pilot should go off.
2. Pilot gas flow should stop within 30 seconds.
Part Description
Main Burner Orifice, Front
Main Burner Orifice, Rear
SIT Gas Valve Conversion Kit
Gas Conversion Label
Tools Needed: Standard Screwdriver, 1/4 Inch Hex Driver, 5/16 Inch Hex Driver, 7/16 Inch Wrench, and 7/16 Inch Deep
Socket Set
41339-2-0220
GAS CONVERSION INSTRUCTIONS
DIRECT - VENT GAS FIREPLACE
CONVERSION KITS
Model
FOR CONVERSION TO PROPANE GAS
CHECK THE SAFETY SHUTDOWN PERFORMANCE
Conversion Kit - 37506
Empire Comfort Systems Inc. • Belleville, IL
WARNING
WARNING
PARTS LIST
P287
P208
R11382
1224
Part No.
37506
Quantity Supplied
1
1
1
1
Page 1
Publicité
Manuels Connexes pour Empire Comfort Systems DVCT36CBP9-1
Sommaire des Matières pour Empire Comfort Systems DVCT36CBP9-1
- Page 1 FOR CONVERSION TO PROPANE GAS WARNING This conversion kit is to be installed by an Empire Comfort Systems, Inc., distributor (or other qualified agency¹)* in accordance with the manufacturer’s instructions and all codes and requirements of the authority having jurisdiction. Failure to follow instructions could result in serious injury or property damage.
- Page 2 FRONT 3. Remove front and rear burners by removing screws on left and pulling out towards left side. See Figure 2. Figure 5 Figure 2 7. Use a 7/16 inch deep socket set to remove front and rear orifices. 4. Remove (2) screws holding pilot assembly to burner pan. 8. Use a 7/16 inch deep socket set to install orifice marked This will allow pilot assembly to drop. See Figure 3. “1.45” in rear orifice holder and “#56” in front orifice holder. REAR REAR FRONT FRONT Figure 6 Figure 3 Page 2 Empire Comfort Systems Inc. • Belleville, IL 41339-2-0220...
- Page 3 Also indicate OPEN CLOSED conversion by adding “Conv.” behind type of gas. Figure 7 11. Using a 7/16 inch open wrench, loosen pilot body by slightly turning counter-clockwise. Slide orifice bracket to other side and tighten pilot body clockwise. See Figure 8. “LP” MARKING (HOLE, RED PAINT) Figure 8 12. Replace items removed in steps 2-5 in reverse order. 13. Gas conversion completed. 41339-2-0220 Empire Comfort Systems Inc. • Belleville, IL Page 3...
- Page 4 Empire Comfort Systems Inc. Belleville, IL If you have a general question about our products, please e-mail us at info@empirecomfort.com. If you have a service or repair question, please contact your dealer. www.empirecomfort.com Page 4 41339-2-0220...
-
Page 5: Conversion Pour Changement De Gaz Foyer Au Gaz À Ventilation Directe
37506 POUR CONVERSION AU GAZ PROPANE AVERTISSEMENT Ce nécessaire de conversion doit être installé par un distributeur Empire Comfort Systems Inc. (ou une agence qualifiée )* conformément aux instructions du fabricant et à tous les codes et exigences de l’autorité ayant juridiction. Le défaut de respecter les directives pourrait résulter en de grave blessure ou dégâts matériels. - Page 6 3. Déposer les brûleurs avant et arrière en retirant les vis à AVANT gauche et en tirant vers le côté gauche. Voir Figure 2. Figure 5 Figure 2 7. Utiliser un jeu de douilles longues de 7/16 po pour retirer les orifices avant et arrière. 4. Retirer deux (2) vis qui fixent la veilleuse à la cuvette du brûleur. Ceci permet à l’ensemble de veilleuse de 8. Utiliser un jeu de douilles longues de 7/16 po pour tomber. Voir Figure 3. poser l’orifice marqué « 1,45 » dans le porte-orifice arrière et l’orifice « #56 » dans le porte-orifice avant. ARRIÈRE AVANT Figure 3 Figure 6 Page 2 Empire Comfort Systems Inc. • Belleville, IL 41339-2-0220...
- Page 7 FERMÉ Si le foyer n’est pas installé ou que la carte Figure 7 d’enregistrement du produit n’a pas été retournée à Empire Comfort Systems, cocher le type de gaz converti 11. Utiliser une clé ouverte de 7/16 po pour desserrer le sur la carte. Indiquer également la conversion en ajoutant corps de la veilleuse en tournant légèrement en - sens « Conv. » derrière le type de gaz. antihoraire. Faire glisser l’attache de l’orifice de la veilleuse vers l’autre côté et le serrer en tournant en sens horaire. Voir Figure 8. INSCRIPTION « LP » (TROU, PEINTURE ROUGE) Figure 8 12. Remplacer en ordre inverse les éléments retirés aux étapes 2 à 5. 13. La conversion du gaz est terminée. 41339-2-0220 Empire Comfort Systems Inc. • Belleville, IL Page 3...
- Page 8 Empire Comfort Systems Inc. Belleville, IL Pour toute question générale concernant nos produits, veuillez nous envoyer un courriel à info@empirecomfort.com. Pour toute question d’entretien ou de réparation, veuillez communiquer avec votre revendeur. www.empirecomfort.com Page 4 41339-2-0220...