Publicité
CLEANING
To Clean Trims:
1. Gently wipe with soft, clean, dry lint-free cloth to
remove dust.
2. Wipe with mild detergent solution on a soft, clean
cloth to remove fingerprints and stains.
3. Rinse with clean water and dry with soft, clean, dry
lintfree cloth.
DRIVER REPLACEMENT
Caution: To avoid possible electric shock, be sure
that power supply is turned off before removing
and replacing driver. Driver replacement should
be completed by a "qualified electrician".
1. Remove trim/LED module assembly by pulling down
from edges of the trim flange, and squeezing torsion
springs to release from frame.
2. Disconnect LED module flex wire whip.
3. Remove junction box cover that has driver attached.
4. Disconnect "line", "common" and "ground" wires
from driver. Disconnect red and blue light engine
wires from driver.
5. Remove two screws attaching driver to junction box
cover and attach new driver with same screws.
6. Reconnect "line", "common", "ground" and red and
blue light engine wires to new driver.
7. Reattach junction box cover with driver back to
junction box and resume normal operation.
8. Reconnect LED module and reinstall trim/LED
module assembly.
Wiring Diagrams for D010
Connector
Connector
REMPLACEMENT DU CONDUCTEUR
Attention: Pour éviter toute possibilité de choc
électrique, vérifiez que l'alimentation est coupée
avant d'enlever ou de remplacer le conducteur. Le
remplacement du conducteur doit être réalisé par
un électricien qualifié..
1. Dégagez la garniture/le module DEL du cadre en
tirant sur les bords de la bride de garniture vers le
bas et en pressant les ressorts de torsion.
2. Déconnectez les faisceaux de câbles souples du
module DEL.
3. Retirez le couvercle de la boîte de jonction auquel
le conducteur est fixé.
4. Débranchez les fils "alimentation", "neutre" et
"terre" du conducteur. Débranchez les fils du moteur
lumière rouge et bleu du conducteur.
5. Retirez les deux vis qui fixent le conducteur au
couvercle de la boîte de jonction et fixez le nouveau
conducteur avec les mêmes vis.
6. Rebranchez les fils "alimentation", "neutre" et
"terre", ainsi que les fils rouge et bleu sur le
nouveau conducteur.
7. Rattachez le couvercle équipé du conducteur sur
la boîte de jonction et remettez en fonctionnement
normalement.
8. Connectez le module à DEL de nouveau et
réinstallez la garniture/le module DEL.
Schémas de câblage pour D010
Connecteur
Connecteur
COOPER LIGHTING SOLUTIONS
HC8 LED Commercial Open Frame Installation
DRIVER REPLACEMENT
Caution: To avoid possible electric shock, be sure
that power supply is turned off before removing
and replacing driver. Driver replacement should
be completed by a "qualified electrician".
1. Remove trim/LED module assembly by pulling down
from edges of the trim flange, and squeezing torsion
springs to release from frame.
2. Disconnect LED module flex wire whip.
3. Remove junction box cover that has driver attached.
4. Disconnect "line", "common" and "ground" wires
from driver. Disconnect red and blue light engine
wires from driver.
5. Remove two screws attaching driver to junction box
cover and attach new driver with same screws.
6. Reconnect "line", "common", "ground" and red and
blue light engine wires to new driver.
7. Reattach junction box cover with driver back to
junction box and resume normal operation.
8. Reconnect LED module and reinstall trim/LED
module assembly.
Diagramas de cableado para D010
Conector
Conector
IB517032ML
Installation instructions
5
Publicité
