camry Premium CR 7720 Mode D'emploi page 6

19. Place the fan heater only on flat, stable surface
20. Always turn the fan heater off and set the thermostat dial to minimum before removin
the power plug from the socket.
21. Never use the fan heater in high humidity rooms – bathroom, shower room, swimming
pools etc. The humidity can cause short circuit, and effect in damaging the device.
22. The operating fan heater needs to be under supervision and in sight all the time. If you
are leaving the room with the fan heater, always turn the fan heater off. If the fan heater is
not used, the power plug has to be removed from the power outlet.
23. Do not connect the fan heater to the automatic switching device, for example
temperature controlling device or time switch.
24. Flammable materials, for example furniture, bedclothes, paper, clothes, curtains should
be kept at least one meter from the fan heater.
25. Do not cover the device or put any objects on it while it is operating. Do not use the
device to dry clothes.
26. The power cord should not be placed above the fan heater, and it should not touch or
be placed near hot surfaces of the fan heater. Do not place the fan heater directly under
the power outlet.
27. The heating surfaces can heat to a temperature of 60 °C or higher. The fan heater
should be in a place that children and animals do not have access to.
28. The device is not intended to be installed or used in vehicles.
29. Some parts inside the device can be hot or cause sparking. Do not use the fan heater in
places, where gasoline, paints or other flammable materials are used or stored.
PRODUCT DESCRIPTION: LED CERAMIC FAN HEATER
1. Control Panel
3. Heat outlet
5. Power switch
CONTROL PANEL
A. ON/OFF / Standby Mode button
C. Oscillation button
E. Temperature adjustment button
G. High heat level 1800W icon
H. Timer activation icon
USSING THE DEVICE
1. Once the power switch (5) on the rear of the device has been switched on, use the On/Off switch (A) to power on the device. Once
pressed the other functions will be activated.
2. By pressing the heating button (B) once will activate low heating level, the display will light up icon (F). By pressing a second time will
activate high heating level, the display will light up icon (G). When pressed the heating button (B) a third time heat mode will be
switched off.
3. By pressing the temperature adjustment button (E) the desired temperature can by adjusted in range 10-35°C. Desired temperature
level will be shown on the display by icon (H). To decrease temperature press the temperature adjustment (E) button too. When
desired room temperature would be achieved the device will stop heating. The device will blow air with a temperature close to the
content of the ambient temperature.
4. By pressing the timer button (D) chose desired time operation from 1 to 8 hours. Display will light up the icon (I). When the time has
elapsed the device will power off.
5. By pressing the oscillation button (C) - keep it longer time - to activate left – right direction oscillation, to deactivate press again.
6. After operation, press the On/Off switch (A), the device will cool down automatically and switch off after 30 seconds.
SAFETY PORTECTION
1. OVER TIP SWITCH Your heater is designed to automatically shut the heater off when tipped forward or backward. The unit will
automatically turn on once it is returned to its normal upright position. Do not use on thick and long pile carpets, as the heater may not
work, due the tip over switch not been activated.
2. OVERHEAT PROTECTION In the event of abnormal overheating, a safety device shuts down the appliance automatically. After a short
cooling down phase, the appliance is ready for use again. If you still notice the same defect as above mentioned, remove the plug
from the socket and consult your authorized dealer to your after-sales service department.
WARNING: During use, do not touch or cover the air inlet and air outlet.
CLEANING AND MAINTENANCE
1. Make sure the fan heater is not hot.
2. Before cleaning the device remove the plug from the electrical socket.
3. Keep the air inlet and outlet openings clean. Do not allow dust to collect on the openings.
2. Digital display
4. Tip-over switch (located on the base)
6. Carry handle
B. Heat button
D. Timer button
F. Low heat 900W icon
I. Desired temperature level icon
7. Power cord
6