Publicité
Liens rapides
PKCP75XX
Bolt Action Magnum Pen Kit
PKCP7500 • PKCP7510 • PKCP7520 • PKCP7530
Kit Features:
• Easy to turn with single tube
• Minimum Parts to assemble
• Uses Parker® Style Refill
• Available Multiple finishes
• Overall length 5-1/4"
• Now with two Bolt positions
Required Accessories:
• 7 mm, pen mandrel
• Drill bit 10mm #PK10-10
• PKCP7000BU bushing set (2 pc)
• PKTRIMKIT barrel trimming set, use 10mm shaft
• Live Tailstock Center
• 2 part epoxy glue or insta-cure (cyanoacrylate) glue
• Minimum Blank size: 3/4" x 2-1/4"
DIAGRAM A - Parts List
Front End
Spring
Preparing the Blank
• Cut one pen blank to the length of the brass tube (add 1/16" for trimming).
• Drill a 10mm hole lengthwise through the blank.
• Spread the glue over the tube. Insert the tube into the blank with a twisting motion to spread the
glue evenly inside. Center the tube lengthwise in the blank.
• When the glue dries, Square the end of each blank. Use a Barrel trimmer with 10mm shaft or a universal pen
blank squaring jig with a power disc sander. Take the wood down to the brass tube. Do not trim
beyond the length of the tube since this may interfere with operation of the mechanism and assembly.
Use the barrel trimmer shaft to clean the inside of the tube.
Threaded Nut
Tube / Barrel
2-1/16"
Refill
PSI Woodworking Products
Back End Assembly
Position A
Position B
Rotate Bolt
Rotate Clip
Slot A
Cap
Slot B
Publicité
Manuels Connexes pour PSI Woodworking Products Magnum PKCP7500
Sommaire des Matières pour PSI Woodworking Products Magnum PKCP7500
- Page 1 PKCP75XX PSI Woodworking Products Bolt Action Magnum Pen Kit PKCP7500 • PKCP7510 • PKCP7520 • PKCP7530 Kit Features: • Easy to turn with single tube • Minimum Parts to assemble • Uses Parker® Style Refill • Available Multiple finishes • Overall length 5-1/4” • Now with two Bolt positions Required Accessories: • 7 mm, pen mandrel • Drill bit 10mm #PK10-10 • PKCP7000BU bushing set (2 pc) • PKTRIMKIT barrel trimming set, use 10mm shaft • Live Tailstock Center • 2 part epoxy glue or insta-cure (cyanoacrylate) glue • Minimum Blank size: 3/4” x 2-1/4”...
- Page 2 PKCP75XX PSI Woodworking Products DIAGRAM B - Turning the Blanks Blank knurled nut headstock live center 7mm spacer bushings mandrel barrel 7mm spacer wood bushing bushings bushing Turning The Blanks • Mount the bushings and blank according to Diagram B. • Thread on the knurled nut and hand tighten to hold all components in place. • S lide the tailstock up snugly against the mandrel shaft inserting the live center point into the mandrel dimple, lock in place. • H and tighten the quill adjustment to firm up the mandrel. (DO NOT overtighten, it could damage the mandrel. • U sing sharp tools, turn the blank down close to the bushing diameter. Turn the barrel (straight or to a profile of your choice) • Sand the blank down to be flush with the bushings gradually increasing the sandpaper grits.
- Page 3 Traduction des instructions de Penn State Industries (PSI) pour stylo à bille Magnum à mécanisme à verrou (Magnum Bolt Action) Bolt Action Magnum Pen Kit Trousse pour stylo Magnum à mécanisme à verrou PKCP7500 • PKCP7510 • PKCP7520 • PKCP7500 • PKCP7510 • PKCP7520 • PKCP7530 PKCP7530 Kit Features: Caractéristiques de la trousse :...
- Page 4 Traduction des instructions de Penn State Industries (PSI) pour stylo à bille Magnum à mécanisme à verrou (Magnum Bolt Action) • When the glue dries, Square the end of • Lorsque la colle est sèche, équarrissez les extrémités du each blank. Use a Barrel trimmer with 10mm carrelet à...
- Page 5 Traduction des instructions de Penn State Industries (PSI) pour stylo à bille Magnum à mécanisme à verrou (Magnum Bolt Action) • Rotate the clip to slot B (press into slot)- do • Tournez l’agrafe jusqu’à la fente B (insérez-la dans la fente en this by Unscrewing the Cap and rotating the appuyant);...