Publicité
Liens rapides
PKCP82XX
Mini 30 Cal. Bolt Action Pen Kit
PKCP8200 • PKCP8210 • PKCP8220
Kit Features:
• Easy to turn with single tube
• Minimum Parts to assemble
• Uses Mini Style Refill
• Available Multiple finishes
• Overall length 4"
• Now with two Bolt positions
Required Accessories:
• 7 mm, pen mandrel
• Drill bit 3/8" #PKEXEC-3/8
• PKCP3000BU bushing set (2 pc)
• PKTRIMKIT barrel trimming set, use 3/8" shaft
• Live Tailstock Center
• 2 part epoxy glue (PKGLUE2) or insta-cure (cyanoacrylate) glue
• Minimum Blank size: 5/8" x 1-1/2"
Front End
Spring
Preparing the Blank
• Cut a pen blank to the length of the brass tube (add 1/16" for trimming).
• Drill a 3/8" hole lengthwise through the blank.
• Spread the glue over the tube. Insert the tube into the blank with a twisting motion to spread the
glue evenly inside. Center the tube lengthwise in the blank.
• When the glue dries, Square the end of each blank. Use a Barrel trimmer with 3/8" shaft or a universal
pen blank squaring jig with a power disc sander. Take the wood down to the brass tube. Do not trim
beyond the length of the tube since this may interfere with operation of the mechanism and assembly.
Use the barrel trimmer shaft to clean the inside of the tube.
DIAGRAM A - Parts List
Tube / Barrel
1-3/8"
Mini Refill
PSI Woodworking Products
Publicité
Manuels Connexes pour PSI Woodworking Products PKCP82 Serie
Sommaire des Matières pour PSI Woodworking Products PKCP82 Serie
- Page 1 PKCP82XX PSI Woodworking Products Mini 30 Cal. Bolt Action Pen Kit PKCP8200 • PKCP8210 • PKCP8220 Kit Features: • Easy to turn with single tube • Minimum Parts to assemble • Uses Mini Style Refill • Available Multiple finishes • Overall length 4” • Now with two Bolt positions Required Accessories: • 7 mm, pen mandrel • Drill bit 3/8” #PKEXEC-3/8 • PKCP3000BU bushing set (2 pc) • PKTRIMKIT barrel trimming set, use 3/8” shaft • Live Tailstock Center • 2 part epoxy glue (PKGLUE2) or insta-cure (cyanoacrylate) glue • Minimum Blank size: 5/8” x 1-1/2”...
- Page 2 PKCP82XX PSI Woodworking Products DIAGRAM B - Turning the Blank Blank knurled nut headstock live center 7mm spacer bushings mandrel barrel 7mm spacer wood bushing bushings bushing Turning The Blank • Mount the bushings and blank according to Diagram B. • Thread on the knurled nut and hand tighten to hold all components in place. • S lide the tailstock up snugly against the mandrel shaft inserting the live center point into the mandrel dimple, lock in place. • H and tighten the quill adjustment to firm up the mandrel. (DO NOT overtighten, it could damage the man- drel.
- Page 3 Traduction des instructions de Penn State Industries (PSI) pour stylo Bolt Action miniature Mini 30 Cal. Bolt Action Pen Kit Stylo Bolt Action miniature « Balle de calibre 30 » Kit Features: Caractéristiques de la trousse : • Easy to turn with single tube •...
- Page 4 Traduction des instructions de Penn State Industries (PSI) pour stylo Bolt Action miniature knurled nut Écrou moleté Live center Pointe vive 7 mm spacer bushings Bagues d’espacement de 7 mm End bushing Bague d’extrémité Barrel Barillet Wood Bois Mandrel Mandrin Turning The Blank Tournage du carrelet •...
- Page 5 Traduction des instructions de Penn State Industries (PSI) pour stylo Bolt Action miniature screw driver with a small head, insert into the back long avec une petite tête, insérez dans l’extrémité arrière tel end as shown. qu’illustré. Rotate the bolt as necessary and tighten the set Pivotez le verrou dans la mesure nécessaire et serrez la vis de calage.