Table des Matières
Publicité
RF Rx SW868/SW915/SW917/SW922-4W 24VAC/DC
//
Montage- und Anschlussanleitung / Funkempfänger
Mounting and wiring instructions / Wireless receiver
Instructions de montage et de câblage / Récepteur sans fil
Istruzioni di montaggio e collegamento / Ricevitore wireless
Instruções de montagem e instalação / Receptor sem fio
Инструкция по монтажу и подключению / Радио-приемник
English
Logic
LED 1
LED 2
function
OR
on
-
AND
-
on
XOR
-
-
Operation mode wiping contact
- Select wiping function -> LED MD flashes fast.
- Set the time of the wiping contact. The pre-set time can be changed
with push-button S2. -> Observe LED display (see table).
- During mode »wiping time flexible«, count the pulses of the flashing
LED 4 and confirm the time achievement (1 s/pulse) with push-
button S1.
- In order to change set time of the wiping contact, start selection of
operation mode and select wiping function again.
Time of wip-
LED 1
LED 2
ing contact
500 ms
-
-
1 s
on
-
2 s
-
on
5 s
-
-
flexible
-
-
Operation mode status monitoring
- After selection of status monitoring the LED MD flashes
every second.
- The LEDs 1 - 4 indicate the adjustable status times.
- The display of the LED changes every 5 s (see table).
- When the required LED combination is indicated, press the push-
button S1 for 1 s. The desired operation mode is now activated.
- Without confirmation of the selection, the default value of 10 s will
be set.
Status signal
LED 1
LED 2
time
10 s
on
-
100 s
on
on
1 000 s
on
on
10 000 s
on
on
Function: If no status information is given by the taught-in switches,
relay K4 automatically triggers the alarm after the status time has
elapsed 2.2 times.
Attention! Please ensure that the taught-in wireless transmitter is set
to the correct status signal time.
LED 3
LED 4
LED MD
-
-
flashing
-
-
flashing
on
-
flashing
LED 3
LED 4
LED MD
-
-
flashing
-
-
flashing
-
-
flashing
on
-
flashing
-
flashing
-
LED 3
LED 4
LED MD
-
-
flashing
-
-
flashing
on
-
flashing
on
on
flashing
Teaching in of switches
- Press push-button S1 approx. 1 s -> LED MD flashes slowly (1 Hz).
- Channel selection: press push-button S2.
- Actuate switch/command device to be taught in -> the LED of the
corresponding channel is off for a short time.
- To leave teach-in mode: press push-button S1 approx. 1 s -> LED MD
lights up.
Deleting one switch
- Press push-button S1 for 5 s -> LED MD flashes fast, LED 1 lights up.
- Channel selection: press push-button S2.
- Actuate switch/command device to be deleted -> the LED of the
corresponding channel is off for a short time.
- To leave delete mode: press push-button S1 approx. 1s -> LED MD
is green.
Inverse teaching in of one switch
- Procedure like teach-in but switch/command device must be actuat-
ed before procedure is started by pressing S1.
Deleting all switches + reset operating mode
- Press push-button S1 for 5 s -> LED MD flashes fast, LED 1 lights up.
- Release push-button S1.
- Repress push-button S1 for 5 s until LED MD is off and LED 1
is flashing.
- Operation mode is set back to standard, teaching in of the switches
is cancelled.
- Release push-button S1 -> receiver is restarting.
Maintenance
With rough conditions, we recommend routine maintenance as follows:
1. Remove all dirt or particles.
Cleaning
- In case of damp cleaning: use water or mild, non-scratching,
non-chafing cleaners.
- Do not use aggressive cleaners or solvents.
Clean enclosure on the outside only. Clean enclosure with household
cleaning agents. Do not use any compressed air to clean.
Disposal
- Observe national, local and legal regulations concerning disposal.
- Recycle each material separately.
6 / 28
Publicité
Table des Matières
