Emerson White-Rodgers F145RF-1600 Instructions D'installation page 4

HOW TO IDENTIFY THE SENSOR NUMBER
At the remote sensor, momentarily press the Connect button
Ž‘…ƒ–‡† ‘ –Š‡ ‹•‹†‡ ‘ˆ –Š‡ •‡•‘” Š‡ 
number assigned.
1 ƒ„‡” ƒ•Š •‡•‘” 1
2 ƒ„‡” ƒ•Š‡• •‡•‘” 2
3 ƒ„‡” ƒ•Š‡• •‡•‘” 3
4 ƒ„‡” ƒ•Š‡• ‘—–†‘‘” •‡•‘” 4
HOW TO CHECK BATTERY STATUS
1. Press the Menu button once on the Comfort Interface and
release.
2. Press the Connect button once and release. Comfort Interface
display will indicate ‡ƒ”…Š‹‰ until (CTL) control is found.
3. Continue pressing and releasing the Next „—––‘ –‘ ˜‹‡™
the battery icon for all remote sensors (RS 1, RS 2, RS 3 or
ORS). If battery needs to be replaced "Change
displayed for the remote sensor listed on the screen.
REMOVE WIRELESS DEVICES FROM THE WIRELESS SYSTEM
1. At the Comfort Interface, press Menu button once.
2. Press the Connect button.
3. Press and release the Next button until the display shows the
†‡˜‹…‡ ›‘— ™ƒ– –‘ †‡Ž‡–‡ CTL, RS 1, RS 2, RS 3 or ORS.
 “—‹’‡– ‘–”‘Ž ‘†—Ž‡
RS 1 (Indoor remote sensor 1)
RS 2 (Indoor remote sensor 2)
RS 3 (Indoor remote sensor 3)
ORS (Outdoor remote sensor 4)
RAS (Return Air Sensor - do not delete)
4. Press and hold the and
†‡Ž‡–‡ –Š‡ †‡˜‹…‡ ˆ ƒ††‹–‹‘ƒŽ †‡˜‹…‡• ‡‡† –‘ „‡ †‡Ž‡–‡†
press Next —–‹Ž –Š‡ †‹•’Žƒ› •Š‘™• –Š‡ ‡š– †‡˜‹…‡ –‘ †‡Ž‡–‡
5. Press the Run button to exit the menu.
TROUBLESHOOTING
Symptom
The Comfort Interface display will alternately
ƒ•Š –Š‡ –‹‡ ƒ† –‡’‡”ƒ–—”‡ ƒ† ‡‘–‡
Sensor number (RS 1, RS 2, RS 3 or ORS) and
two dashes (--)
Š‹–‡ ‘†‰‡”• ‹• ƒ †‹˜‹•‹‘
of Emerson Electric Co.
The Emerson logo is a
–”ƒ†‡ƒ” ƒ† •‡”˜‹…‡ ƒ”
of Emerson Electric Co.
™‹ŽŽ ƒ•Š –Š‡ •‡•‘”
will be
buttons simultaneously to
Possible Cause
‡‘–‡ ‡•‘” ƒ† “—‹’‡– ‘†—Ž‡
are located too far apart.
Batteries are dead.
www.white-rodgers.com
www.emersonclimate.com
Sensor
battery
Correction Action
‡Ž‘…ƒ–‡ ‡‘–‡ ‡•‘” …Ž‘•‡” –‘ “—‹’‡–
Control Module.
Replace batteries.