1. Manuels
  2. Marques
  3. R&G Manuels
  4. Accessoires de moto
  5. BLGFK0011
  6. Instructions de montage

R&G BLGFK0011 Instructions De Montage

Masquer les pouces
1
2
3
4
5
6
7

Publicité

Table des Matières

Page 1 of 7
BLGFK0011
FITTING INSTRUCTIONS FITTING INSTRUCTIONS FOR BLGFK0011
BRAKE LEVER-GUARD FITTING KIT
KAWASAKI Z650 2017-
T
.
HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE
S
.
OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY
D
.
O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT
P
.
LEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS
OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
P
LEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF
.
MOUNTING TO THE BIKE
I
,
N THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS
.
THESE RUBBER WASHERS CAN BE THROWN AWAY
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM:
WWW.RG-RACING.COM
R&G Racing
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
www.rg-racing.com
Email:
info@rg-racing.com

Publicité

Table des Matières
loading

Manuels Connexes pour R&G BLGFK0011

Sommaire des Matières pour R&G BLGFK0011

  • Page 1 Page 1 of 7 BLGFK0011 FITTING INSTRUCTIONS FITTING INSTRUCTIONS FOR BLGFK0011 BRAKE LEVER-GUARD FITTING KIT KAWASAKI Z650 2017- HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT...

  • Page 2: Tools Required

    Page 2 of 7 BLGFK0011 TOOLS REQUIRED GENERAL TORQUE SETTINGS • ALLEN TOOL SET TO INCLUDE 5mm A/F SIZE. M4 BOLT = 8Nm M5 BOLT = • SPECIFIC TOOLS REQUIRED TO REMOVE OEM BAR-ENDS, IF APPLICABLE. M6 BOLT = M8 BOLT = 20Nm...

  • Page 3: Fitting Instructions

    Page 3 of 7 BLGFK0011 PICTURE 1 FITTING INSTRUCTIONS • To fit the Brake Lever Guard, the original bar end needs to be removed. Roll up the end of handle- bar grip inwards so the tip of OEM slider clips can be seen (in the handlebar). Spray the OEM slider assembly with appropriate lubricant, this is to help to slide the whole slider assembly out.
  • Page 4 Page 4 of 7 BLGFK0011 • Finally, push the flat cap (item 8) into the head of the cap-head bolt to give a clean look. IMPORTANT - WHEN FITTING THIS PRODUCT, IT IS YOUR RESPONSIBILITY TO ENSURE THAT THE PRODUCT IN NO WAY IMPEDES THE OPERATION OF THE MOTORCYCLE AND IS CHECKED REGULARLY FOR TIGHTNESS AND CORRECT OPERATION.
  • Page 5 Page 5 of 7 BLGFK0011 NOTICE DE MONTAGE POUR BLGFK0011 PROTÈGE LEVIER DE FREIN KAWASAKI Z650 2017- E KIT CONTIENT LES ARTICLES ILLUSTRES ET ETIQUETES SUR LA PAGE ERTAINES PARTIES PEUVENT ETRE PRESENTES UNIQUEMENT POUR LA CLARTE DES INSTRUCTIONS E PAS PROCEDER AU MONTAGE TANT QUE VOUS N...

  • Page 6: Outils Requis

    Page 6 of 7 BLGFK0011 OUTILS REQUIS VALEURS DE SERRAGE RECOMMANDÉES • CLÉ ALLEN 5mm. M4 BOULON = 8Nm • OUTIL SPÉCIFIQUE POUR ENLEVER LES M5 BOULON = 12Nm EXTRÉMITÉS DE GUIDON, SI POSSIBLE. M6 BOULON = 15Nm M8 BOULON = 20Nm...
  • Page 7 Page 7 of 7 BLGFK0011 NOTICE DE MONTAGE • Pour installer le protège levier de frein, l'extrémité de guidon d'origine doit être retirée. Enrouler l'extrémité de la poignée du guidon vers l'intérieur pour que la pointe des clips de glissière d’origine soit visible (dans le guidon).

Table des Matières