General Power Tool Safety Warnings - Makita 9566CR Manuel D'instructions

ENGLISH (Original instructions)
1. Shaft lock
2. Slide switch
3. Indication lamp (speed adjusting
dial)
4. Indication lamp
5. Speed adjusting dial
6. Wheel guard
7. Bearing box
8. Screw
9. Lever
10. Lock nut
SPECIFICATIONS
Depressed center wheel diameter
Max. wheel thickness
Spindle thread
Rated speed (n) / No load speed (
Overall length
Safety class
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
GRINDER SAFETY WARNINGS
Safety Warnings Common for Grinding, Sanding, Wire
Brushing, or Abrasive Cutting-Off Operations:
1. This power tool is intended to function as a
grinder, sander, wire brush or cut-off tool. Read all
safety warnings, instructions, illustrations and
Explanation of general view
11. Depressed center grinding wheel
12. Inner flange
13. Lock nut wrench
14. Abrasive disc
15. Rubber pad
16. Marking A
17. Marking B
18. Marking C
19. Pin
20. Vent
21. Wire cup brush/Wire bevel brush
Model
n
)
0
Net weight
9566CR
150 mm
6.4 mm
M14
10,000 min
299 mm
2.4 kg
specifications provided with this power tool.
ENE048-1
Failure to follow all instructions listed below may result
in electric shock, fire and/or serious injury.
2. Operations such as polishing are not
recommended to be performed with this power
ENF002-2
tool. Operations for which the power tool was not
designed may create a hazard and cause personal
injury.
3. Do not use accessories which are not specifically
designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
GEA010-1
4. The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated
speed can break and fly apart.
5. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
6. Threaded mounting of accessories must match
the grinder spindle thread. For accessories
mounted by flanges, the arbour hole of the
accessory must fit the locating diameter of the
GEB033-8
flange. Accessories that do not match the mounting
hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
7. Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
22. Abrasive cut-off wheel/diamond
wheel
23. Wheel guard for abrasive cut-off
wheel/diamond wheel
24. Abrasive cut-off wheel
25. Diamond wheel
26. Thickness: Less than 4 mm
(5/32")
27. Thickness: 4 mm (5/32") or more
28. Exhaust vent
29. Inhalation vent
9566CVR
150 mm
6.4 mm
-1
10,000 min
299 mm
/II
M14
-1
2.4 kg
5