Important Notice - ACE Instruments AL5500 plus Notice D'utilisation

Alcotest

Masquer les pouces

Table des Matières

Les langues disponibles

This way you receive results that are as accurate as possible:

Wait at least 15 minutes after your last sip of alcohol.

Do not eat, drink or smoke during that time.

Do not open the casing.

Do not keep the breathalyzer in cold, hot, moist or

badly ventilated places.

Keep the breathalyzer out of the reach of children.

Conduct three inlet tests after long storage before

conducting the actual alcohol test.

Do not drop the breathalyzer.

Change the battery if it is depleted. Diminished battery

capacity leads to incorrect test results.

Do not conduct tests in loud (sound waves disrupt the

sensor), drafty or poorly ventilated places.

After a test result of 1.000‰ (per mill = default setting) or

higher the sensor needs rest time. In this case wait at least

three minutes before the next test.

Do not conduct tests in very cold, very hot or an unventilated,

smoky ambience.

Store the breathalyzer in a way to avoid penetration

by dust or liquids.

Blowing too hard may cause damage to the sensor as saliva

flows into it.

ACE INSTRUMENTS RECOMMENDS:

ALWAYS USE A NEW MOUTHPIECE FOR EACH PERSON AND

TEST THAT IS CONDUCTED. ACE INSTRUMENTS ASSUMES NO

LIABILITY FOR ANY DAMAGES WHICH ARISE WHEN SEVERAL

PEOPLE USE THE SAME MOUTHPIECE FOR MULTIPLE TESTS.

ONLY USE THE PROVIDED SINGLE PACKED AND

HYGIENIC MOUTHPIECES - MORE ARE AVAILABLE AT

WWW.ACE-INSTRUMENTS.NET.

DURING EACH TEST THE BREATHALYZER´S INTERNAL AND

EXTERNAL PARTS COME INTO CONTACT WITH HUMAN SECRE-

TION (SALIVA, BLOOD, SWEAT, ETC.)! USE DISPOSABLE GLOVES

WHEN PULLING OUT A MOUTHPIECE USED BY ANOTHER

PERSON! YOU CAN BUY APPROPRIATE GLOVES E.G. AT ACE

TECHNIK (WWW.ACE-TECHNIK.DE).

Conducting the measurement:

If you use the breathalyzer for the first time, then push the

battery compartment cover on the back downwards. Remove

the small paper inside the battery compartment (this paper

prevents the 2 inserted batteries from discharging). Close the

battery compartment cover again.

Insert a mouthpiece (best accuracy) or a straw (good accu-

racy) into the sensor / mouth opening on the front of the breat-

halyzer. Make sure that the mouthpiece / straw is firmly seated.

Use a new mouthpiece / new straw for each test person.

Push the power button*. The device warms up and therefor a

countdown starts. Wait until you can see "0" on the display.

As soon as you can see "0", start blowing into the mouthpiece.

The device will start beeping as soon as you start blowing,

keep blowing steadily until you hear a quick double beep tone.

Tip: Blow like you would whistle (without a break). If the breath

sample was too weak then you can see „Flo" on the display.

Please put off the device and start it again for a new test.

After a successful breath sample you will see the digit „0"

moving left to right in the display as the device analyzes the

breath sample. The test result is displayed after a few seconds

(blinking 10 times). It shows a 3 digit readout (with 2 decimals)

of your blood alcohol level in per mill. You can interprete the

test result 1:1. The test result has got a tolerance of +/- 0,10 per

mill with reference to 0,50 per mill.

You can put the device off by pushing the power button until

you see "Out" on the display and additionally you will hear a

beep tone, but the device also puts itself off automatically

approx. 15 seconds after showing the blinking test result.

*If you constantely keep pushing the power button, you can

see the number of all tests conducted with the device (starting

with zero after a calibration) and also the last result of measu-

rement where alcohol was detected.