STERWINS EVB2.4 Notice De Montage, Utilisation Et Entretien page 176

POWER TOOL FOR OPERATIONS DIFFERENT FROM THOSE INTENDED COULD
FR
RESULT IN A HAZARDOUS SITUATION.
ES
2.8 SERVICE
PT A ) HAVE YOUR POWER TOOL SERVICED BY A QUALIFIED REPAIR PERSON
USING ONLY IDENTICAL REPLACEMENT PARTS. THIS WILL ENSURE THAT
THE SAFETY OF THE POWER TOOL IS MAINTAINED.
IT
2.9 BLOWER USE AND CARE
EL
PL
1TRAINING
A ) READ THE INSTRUCTIONS CAREFULLY. BE FAMILIAR WITH THE
CONTROLS AND THE CORRECT USE OF THE MACHINE.
RU
B ) NEVER ALLOW CHILDREN OR PEOPLE UNFAMILIAR WITH THESE
INSTRUCTIONS TO USE THE MACHINE. LOCAL REGULATIONS CAN RESTRICT
THE AGE OF THE OPERATOR.
KZ
C ) KEEP IN MIND, THAT THE OPERATOR OR USER IS RESPONSIBLE FOR
ACCIDENTS OR HAZARDS OCCURRING TO OTHER PEOPLE OR THEIR PROPERTY.
UA
2PREPARATION
A ) OBTAIN EAR PROTECTION AND SAFETY GLASSES. WEAR THEM AT ALL TIMES
RO
WHILE OPERATING THE MACHINE.
B ) WHILE OPERATING THE MACHINE ALWAYS WEAR SUBSTANTIAL
FOOTWEAR AND LONG TROUSERS. DO NOT OPERATE THE MACHINE WHEN
EN
BAREFOOT OR WEARING OPEN SANDALS. AVOID WEARING CLOTHING THAT IS
LOOSE FITTING OR THAT HAS HANGING CORDS OR TIES.
C ) DO NOT WEAR LOOSE CLOTHING OR JEWELLERY THAT CAN BE DRAWN
INTO THE AIR INLET. KEEP LONG HAIR AWAY FROM THE AIR INLETS.
D ) OPERATE THE MACHINE IN A RECOMMENDED POSITION AND ONLY ON A
FIRM, LEVEL SURFACE.
E ) DO NOT OPERATE THE MACHINE ON A PAVED OR GRAVEL SURFACE WHERE
EJECTED MATERIAL COULD CAUSE INJURY.
F ) BEFORE USING, ALWAYS VISUALLY INSPECT TO SEE, THAT THE SHREDDING
MEANS,SHREDDING MEANS BOLTS AND OTHER FASTENERS ARE SECURE, THE
IMPORTANT : READ CAREFULLY BEFORE USE.
KEEP FOR FUTURE REFERENCE.
G ) KEEP HANDLES AND GRASPING SURFACES DRY, CLEAN AND FREE
FROM OIL AND GREASE. SLIPPERY HANDLES AND GRASPING SURFACES
DO NOT ALLOW FOR SAFE HANDLING AND CONTROL OF THE TOOL IN
UNEXPECTED SITUATIONS.
B ) IF THE SUPPLY CORD OF THIS POWER TOOL IS DAMAGED, IT MUST BE
REPLACED BY A SPECIALLY PREPARED SUPPLY CORD AVAILABLE THROUGH THE
SERVICE ORGANIZATION.
HOUSING IS UNDAMAGED AND THAT GUARDS AND SCREENS ARE IN PLACE.
REPLACE WORN OR DAMAGED COMPONENTS IN SETS TO PRESERVE BALANCE.
REPLACE DAMAGED OR UNREADABLE LABELS.
G ) BEFORE USE, CHECK THE SUPPLY AND EXTENSION CORD FOR SIGNS
OF DAMAGE OR AGING. IF THE CORD BECOMES DAMAGED DURING USE,
DISCONNECT THE CORD FROM THE SUPPLY IMMEDIATELY. DO NOT TOUCH THE
CORD BEFORE DISCONNECTING THE SUPPLY. DO NOT USE THE MACHINE IF
THE CORD IS DAMAGED OR WORN.
H ) NEVER OPERATE THE MACHINE WHILE PEOPLE, ESPECIALLY CHILDREN, OR
PETS ARE NEARBY.
3OPERATION
A ) BEFORE STARTING THE MACHINE, MAKE CERTAIN THAT THE FEEDING
CHAMBER IS EMPTY.
B ) KEEP YOUR FACE AND BODY AWAY FROM THE FEED INTAKE OPENING.
C ) DO NOT ALLOW HANDS OR ANY OTHER PART OF THE BODY OR CLOTHING
INSIDE THE FEEDING CHAMBER, DISCHARGE CHUTE, OR NEAR ANY MOVING
PART.
D ) KEEP PROPER BALANCE AND FOOTING AT ALL TIMES. DO NOT OVERREACH.
NEVER STAND AT A HIGHER LEVEL THAN THE BASE OF THE MACHINE WHEN
FEEDING MATERIAL INTO IT.
E ) ALWAYS STAND CLEAR OF THE DISCHARGE ZONE WHEN OPERATING THIS
MACHINE.
176