Configuration - Vimar ELVOX 41019 Manuel Installateur

41019
Electronic module for keypad
with white LEDs for backlighting
of the numerical digits
the front module, keystroke
feedback, 1 input that can be
enabled for an additional push
button, 1 NO relay output. Can be
used in outdoor stations Due Fili
Plus or IP. To be completed with
front modules.
1. Description
The keypad module provides entry
control by keying in a personal code for
the entrance panels of the Pixel series.
The module is to be installed in
combination with an electronic audio or
audio-video module of the Pixel Due Fili
or IP series (except art. 41000).
If the entrance panel is equipped with a
display module art. 41018, the keypad
can also be used to make calls to the
indoor units (call function).
2. Characteristics
• Power supply: powered
electronic audio or audio-video module
via a specific cable.
• Power consumption: 90 mA (from
Audio Video or Audio module).
• Operating temperature: -25°C / +55°C.
• Ingress protection rating: IP54.
• Protection rating against impact: IK08
(Pixel), IK10 (Pixel Heavy).
3. Access control function
The device enables activating
programmed command
opening, relay.. ) by
preconfigured code.
3.1. Operation
The keypad has 2 function keys referred
to here as: (Cancel) and
Press the button (Key) to enable
"Code Entry" mode.
If there is no display module, pressing
6
button C quits "Code Entry" mode.
Press button
on
validate the entered code.
In brief:
a. Press button
code entry mode)
b. Press the digit buttons (to enter the
personal code)
c. Press the button
confirm the code entered)
d. Feedback for valid code and
actuation or invalid code feedback.
If the display is installed, pressing
(Cancel) lets you remove the most
recently entered digit; pressing and
holding
deletes all the digits entered previously;
if (Cancel) is held down for a further
two seconds you exit "Code Entry" mode.
You exit "Code Entry" mode also if you
delete all previously entered digits and
then press
If the display is installed, it gives feedback
by the
on the validity of the code entered.
If the above-mentioned buttons are not
pressed for more than 5 seconds, the
system exits code entry mode.

3.2. Configuration

The codes can be managed and defined
by the installer.
If used in combination with a Due Fili
audio or audio-video module, connect
the latter to the PC via USB cable in
order to program the codes. The codes
a can vary in length, up to a maximum
(e.g., lock of 8 digits. A maximum of 2000 codes
entering a
can be saved. Refer to the SaveProg
documentation for specific details.
If used in combination with an IP audio-
video module, for setup refer to the
documentation for Elvox IP and Video
Door IP Manager.
(Key).
4. Call function
If the displaymodule 41018 is installed,
the keypad module can be used to make
a call by directly keying in the desired
(Key) to confirm and
(Key), (to enable
(Key), (to
(Cancel) for two seconds
(Cancel) again.
EN
extension number and confirming it, or
using the keys to search for a name in
the contacts list, where present.
For more information, please refer to the
instructions for art. 41018.
The instruction manual is downloadable
from the site www.vimar.com
Installation rules
Installation should be carried out by
qualified personnel in compliance with
the current regulations regarding the
installation of electrical equipment in the
country where the products are installed.
Conformity
EMC directive. RoHS directive.
Standards EN 62368-1, EN 61000-6-1,
EN 61000-6-3 and EN IEC 63000.
REACH (EU) Regulation no. 1907/2006
– Art.33. The product may contain traces
of lead.
WEEE - Information for
users
If the crossed-out bin symbol
appears on the equipment or
packaging, this means the product must not
be included with other general waste at the
end of its working life. The user must take
the worn product to a sorted waste center, or
return it to the retailer when purchasing a new
one. Products for disposal can be consigned
free of charge (without any new purchase
obligation) to retailers with a sales area of
at least 400m , if they measure less than
2
25cm. An efficient sorted waste collection
for the environmentally friendly disposal of
the used device, or its subsequent recycling,
helps avoid the potential negative effects on
the environment and people's health, and
encourages the re-use and/or recycling of
the construction materials.