Routine Maintenance - Weber GO-ANYWHERE Guide D'utilisation

BEAUTIFUL—
INSIDE AND OUT
Weber grill owners take a
®
lot of pride in their grills. Flaunt
your pride and joy. Keep your grill
clean and beautiful—inside and
out—by following these routine
maintenance steps.
CLEANING THE OUTSIDE OF THE GRILL
To keep the outside of your grill looking its best, use the
following guidelines for safe cleaning.
m WARNING: Turn your Weber
off and wait for it to cool before cleaning
it.
Painted, Enameled and Plastic Surfaces
Use a warm, soapy water solution to clean outside
surfaces; then rinse with water.
IMPORTANT: Do not use cleaners that contain acid,
mineral spirits, or xylene. Do not use oven cleaner,
abrasive cleansers (kitchen cleansers), cleaners that
contain citrus products, or abrasive cleaning pads on
grill.
CLEANING THE INSIDE OF THE GRILL
To keep your grill performing safely and efficiently, it is
important to remove any debris and excess grease that
may have accumulated on the inside of the grill. Use the
following guidelines for safe cleaning.
Inside Lid
Flaking, built-up grease resembles paint flakes. Wipe
inside of lid with paper towel to prevent grease build-up.
Wash inside lid with warm, soapy water; then rinse
with water.
Cookbox Components & Burner Tube
You will need: A stainless steel bristle brush, and a stiff
plastic scraper.
A) Scrape and brush the cooking grate with the scraper
and brush. Remove the cooking grate and set aside.
m CAUTION: Grill brushes should be
checked for loose bristles and excessive
wear on a regular basis. Replace brush
if any loose bristles are found on cooking
grate or brush. Weber recommends
purchasing a new stainless steel grill
brush at the beginning of every spring.
m CAUTION: Do not clean cooking grate in a
self-cleaning oven.
B) Brush any debris off the burner tube. Do not enlarge
burner ports (openings) running along length of
burner tube (1).
C) When cleaning is complete, replace the cooking grate.
Cookbox
Wash inside of cookbox with warm, soapy water; then
rinse with water.

ROUTINE MAINTENANCE

IGNITION SYSTEM OPERATIONS
The igniter supplies a spark to the igniter electrode
assembly. Whether you are performing routine
maintenance or a troubleshooting check on the ignition
system, read the following to keep your ignition system
working properly.
m WARNING: The regulator control knob
should be in the OFF position.
If the igniter fails to ignite your Weber
need to pinpoint where the problem is occurring: with the
gas flow or with the ignition system. Begin by attempting
to match light your burner. Refer to "BURNER IGNITION—
Lighting with a Match." If match lighting is successful, the
problem lies in the ignition system.
MAINTAINING THE PUSH BUTTON IGNITION
SYSTEM
gas grill
®
• Verify that the igniter button pushes in, clicks and
returns to the out position.
• Verify that the tip of the igniter electrode is adjusted to
the proper distance from the holes in the burner tube.
Make sure the tip of the igniter electrode
is adjusted to the proper distance from
the holes in the burner tube. If it is not
adjusted properly, gas can accumulate in
the grill is being igniting. Delayed ignition
of the accumulated gas may occur. This will
result in a fire or explosion which can cause
serious bodily injury or death, and damage
to property.
If the push button ignition system still fails to ignite,
contact the Customer Service Representative in your
area using the contact information on our web site. Log
onto www.weber.com
gas grill, you will
®
DANGER
m
.
®
WEBER-STEPHEN PRODUCTS LLC
www.weber.com
© 2014 Designed and engineered by Weber-Stephen Products LLC,
200 East Daniels Road, Palatine, Illinois 60067 U.S.A.
1
1/8" (3mm)
®