Fitting The Accessories - Moulinex FP7311 Mode D'emploi

Moulf43 27/07/07
Starting your appliance
Electronic model:
- Pulse (intermittent operation): turn
the knob (a6) to the "Pulse" position
By pressing successively for better
control of some preparations.
- Continuous operation: turn the knob
(a6) to the "1" position.
- Stop: turn the knob (a6) to the "0"
position.
- Speed variator (a5): select the speed
indicated or vary it during the
preparation.
Two-Speed Model:
- Pulse (intermittent operation): turn
the knob (a7) to the "Pulse" position
by pressing successively for better
control of some preparations.
- Continuous operation: turn the knob
(a7) to the "1" or " 2 " position
depending on the preparation
- Stop: turn the knob (a7) to the "0"
position.
- Using the upper drive (a2):
check that no accessories are
attached to the lower drive.
The functions of your food
processor
ASSEMBLING THE REMOVABLE
1
PARTS
- Fitting / removing the bowl (b3)
The bowl is used with the following
accessories (depending on model):
- Cutters (e), vegetable cutters (d),
whisk (f), emulsifier (g), citrus press
(h), centrifugal juice extractor with
filter basket (m10) "Maxipress" (l).
- If it is not already fitted, fit the seal
(b3-2) onto the bottom of the
bowl.The lip of the seal must be
facing upwards.
- Fit the drive rod (b3-1) onto the seal
(b3-2).
- Lock the assembly with the nut (b3-3)
until it locks.
- Dismantle the assembly and clean it
after each use.
- Fitting / removing the handles (b4) of
the bowl and (k4) the blender
- For easier cleaning and storage, the
handle of the bowl (b4) and the
blender (k4) can be removed.
- To fit the handle, position it opposite
8:40 Page 23
22
the clips of the bowl.
- Slide the handle upwards until it
clicks into place.
- To remove the handle, press the
release knob (b4-1) or (k4-1) and
slide it downwards.
(Note: the lid of the blender must be
removed to allow the handle (k4) to
be taken off.
The handle (b4) must be fitted to the
bowl so that the upper drive cover (a1)
may be locked
MIXING / BLENDING / MINCING /
2
KNEADING
ACCESSORIES USED
(depending on model)
- Bowl assembly (b), spindle (c), and
cutters (e):
• metal blade (e1) for blending and
chopping.
• plastic kneader (e2) for kneading or
mixing.

FITTING THE ACCESSORIES

Press the release button (a4) to open
the upper drive (a1) cover.
- Place the bowl (b3) on the lower drive
(a3).
- Place the spindle (c) on the bowl drive
(b3-1).
- Slide the metal blade(e1) or the
plastic kneader (e2) onto the spindle
(c), to the bottom of the bowl.
- Place the ingredients in the bowl.
- Fit the lid (b2) or (d4) onto the bowl.
- Close the upper drive cover (a1).
You should hear it "click" shut.
To release the cutters (e) from the
spindle (c):
- Place the assembly on a stable surface.
- Turn the spindle (c) in a clockwise
direction while holding the cutter (e) at
the top.
Recommended speeds
Electronic
Function
Model
Mixing 3-4-5
Chopping 5-Pulse
Kneading 5
Blending 5
Two-Speed
Model
1-2
2-Pulse
2
2