Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
2.2.1 Replace TRS
This procedure allows you to replace the code
highlighted in the grid with a new transmitter
code by following the simple operations as they
appear on your screen. To carry out this operation
the new transmitter must be available. Connect
the PGM449 to the PC using the serial cable, set
the "CONNECT PC" function using the menu
"ADVANCED FUNCTIONS".
Attention! This function is only available for the "non
virtual" codes and only for the 1000-code memory
modules used with the display receiver
2.2.2 TRS Programming
This function allows you to program a new transmitter
with the "virtual code" selected on the grid. Once
programmed, this transmitter can be used on all
receivers where the corresponding "virtual code" has
been memorised. This function is available both for
receivers with 1000-code memory modules (display)
as well as for 300-code memory module receivers.
To carry out transmitter programming you must have
a new transmitter available. Connect the PGM449
to the PC by means of the virtual code hardware
key and set the "Connect PC" function using the
menu "advanced functions".
Delete Installation
Attention: Installation Nr. 10 will be removed
To continue, type in the installation number and press OK,
otherwise press CANCEL.
10
Number:
OK
CANCEL
2.4 Modify
In the modify window it is possible to modify the
installation data and then transfer into a memory
module inserted in the interface on the palm or save
the information in a database to be transferred at
a later date.
Attention! If the "database password" has been
activated and the memory protection PIN code
has been enabled on the Palm you will be asked
to input the PIN number before you can consult
the installation data.
In the layout grid it is possible to modify personal
data/insert new data or enable/disable a channel by
clicking on the corresponding field in the grid.
The transmitter codes cannot be modified directly
but they may be cancelled or new codes may be
added.
It is possible to modify the enable/disable status for the receiver programming buttons (only the receiver with display)
by double clicking the "RCV buttons" check box (green background = "ON"; red background = "OFF").
Replace TRS
Press a key on the TRS
TRS Programming
Connect the programming
key to the transmitter and
press "ENT" on the PGM449
2.3 Delete installation
This procedure allows you to delete an installation from the PC archive
after having typed in the corresponding identity number as shown in
the example on the left.
Modify
ID:
11
Installation:
Apartament block 2
Nr.
27
Address:
Church Ave
Town:
LONDON
Contact:
Installer
Commenti:
PROVA 2
Available memory locations: 1000 code (24LC64)
Memory
Transmitter
CHA
CHB
CHC
CHD
Location
1
X
X
X
X
2
X
X
X
X
3
X
X
X
X
4
X
X
X
X
5
X
X
X
X
6
X
X
X
X
7
X
X
X
X
8
X
X
X
X
9
X
X
X
X
10
X
X
X
X
11
X
X
150000109
12
X
X
150000110
13
X
X
X
X
14
X
X
X
X
15
X
X
X
X
16
X
X
X
X
17
X
X
X
X
18
X
X
X
X
X
SAVE TO
SAVE TO
Add
CANCEL
PGM 449
DATABASE
Codes
13
To cancel press "ESC" on the PGM449
To cancel press "ESC" on the PGM449
RG:
LD
Area LD65WS
Tel.:
01 11223344
Memory type: 1000 code (24LC64)
RCV buttons: ON
User Surname
User Name
V
Code
1
Brown
Jack
2
Wood
Charlie
3
Marley
John
4
5
6
7
8
9
10
X
X
13
14
15
16
17
18
Import
Delete
Import
maintenance
Codes
Codes
personel
Extra
Information
1st User
Setup STRIP
Publicité
Table des Matières
