Lutron EcoSystem 5 Serie Guide D'installation

LED Driver Installation
Best Practices Guide
EcoSystem 5-Series
®
Driver Mounting
Mount driver flush against fixture to provide best heat transfer. Avoid mounting driver close to heat source such as fixture cover plate or light source. Installer is
responsible for ensuring that the driver calibration point does not exceed the maximum rated temperature.
Stud Mounting
(Uses 8 – 32 Threaded Stud)
Correct
Incorrect
Installing or Servicing LED Driver or Light Engine
WARNING: Shock hazard. May result in serious injury or death.
Disconnect power before servicing or installing.
Driver Wiring
For proper wiring, follow wiring schematic on driver being installed. Driver photos are for reference only.
EcoSystem 5-Series, K Enclosure
®
3.00 in (76 mm) W × 1.00 in (25 mm) H × 4.90 in (124 mm) L
Power Wiring
LDE Models
K Enclosure
1
GND
NEU
Power Input
(Line Voltage)
N/C
L
E2
EcoSystem Digital
®
Link (Class 1 or
2,3
Class 2) E1
1 Fixture must be grounded in accordance with local and national electrical codes. Not all
enclosures include ground terminal.
2
Class 2 must be separated from Class 1 and line voltage wiring by the following: 0.25 in
(6 mm) or physical barrier. Please refer to Application Note #142 for further information.
3
EcoSystem Digital Link length is limited by the wire gauge used for E1 and E2 as follows:
®
EcoSystem Digital Link Wiring
®
Wire Gauge Digital Link Length (max)
18 AWG 550 ft
16 AWG 900 ft
14 AWG 1400 ft
12 AWG 2200 ft
Wire Size Digital Link Length (max)
2
0.75 mm 155 m
1.0 mm 2 207 m
1.5 mm 2 310 m
2
2.5 mm 517 m
2
4.0 mm 828 m
To EcoSystem Digital Link compatible devices
®
(up to 64)
K Enclosures
Driver must be electrically grounded for proper performance and to meet UL
K enclosure mounting tabs, grounding should be accomplished by using paint-piercing mounting hardware to ensure
electrical connection through driver enclosure and fixture.
EcoSystem
1.18 in (30 mm) W × 1.00 in (25 mm) H × 14.25 in (362 mm) L
M Enclosure
NEU
Power Input
N/C
(Line Voltage)
E2
EcoSystem Digital
®
Link (Class 1 or
2,3
Class 2) E1
5-Series, M Enclosure
®
Load Wiring
L
Wire Gauge
18 AWG (0.75 mm
16 AWG (1.5 mm
14 AWG (2.5 mm
12 AWG (4.0 mm
Replacement of LED Driver
in the Field
WARNING: Risk of fire or electric shock. LED Retrofit Kit installation
requires knowledge of luminaires electrical systems. If not qualified, do
not attempt installation. Contact a qualified electrician.
WARNING: To prevent wiring damage or abrasion, do not expose
wiring to edges of sheet metal or other sharp objects.
Direct replacement LED drivers shall have the identical part number as the
driver being replaced.
Driver
terminals
THE RETROFIT ASSEMBLY IS ACCEPTED AS A COMPONENT OF A
LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE
DETERMINED BY UL OR AUTHORITIES HAVING JURISDICTION.
Lutron Technical Support Hotline
®
Lutron, ), and EcoSystem are registered trademarks of Lutron Electronics Co., Inc.
NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts.
UL is a registered trademark of Underwriters Laboratories, Inc.
www.lutron.com
Tab Mounting
M Enclosure
and NEC requirements. When using
® ®
Wire Strip Length
For power, output, and digital terminals
(E1, E2).
5/16 in (8 mm)
Note: Class 2 output designed to withstand hot swap.
See table below
Maximum Lead Length
200 mA –700 mA 710 mA –1.5 A 1.51 A –2.10 A
2 ) 30 ft (9 m) 15 ft (4.5 m)
2
) 35 ft (10.5 m) 25 ft (7.5 m)
2
) 50 ft (15 m) 40 ft (12 m)
2 ) 100 ft (30 m) 60 ft (18 m)
Solid copper wire
18 –16 AWG
2
(0.75 –1.5 mm )
–V (Black)
LED light source
+V (Red)
10 ft (3 m)
15 ft (4.5 m)
25 ft (7.5 m)
40 ft (12 m)
1.800.523.9466
P/N 041479a
11/2014