Power Supply; Setting Into Operation - IMG STAGELINE TXS-871HSE Mode D'emploi

4 Power supply

•
Insert only batteries of the same type and
always replace all batteries .
•
If the unit is not used for a longer period
(e . g . more than a week), remove the bat-
teries . Thus, the unit will not be damaged
in case of battery leakage .
1) Press down the two latching buttons (8)
on the sides of the transmitter . The control
part will unlock and can be moved in its
casing .
Slide the control part downwards until
it locks into place again . This will allow
access to the battery compartment (11) on
the rear side of the transmitter (see fig . 3) .
2) Insert two 1 .5 V batteries of size AA (R6)
into the battery compartment, with the
positive and negative connections as indi-
cated in the compartment .
3) Unlock the control part, slide it back to its
previous position until it locks into place .
Never put discharged batteries in the
household waste . To protect the envi-
ronment, always take them to a special
waste disposal, e . g . collection container
at your retailer .

5 Setting into Operation

1) Connect a headband microphone or tie-
clip microphone (e . g . the headband micro-
phone HSE-110 or the tie-clip microphone
ECM-402L from MONACOR) to the mini
XLR jack (4) .
2) To switch on, set the power switch (2) to
ON . The display (3) indicates the transmit-
ting frequency adjusted and a battery sym-
bol which indicates the current charging
status of the batteries in several steps:
full
3) Press down the latching buttons (8) on the
sides of the transmitter and slide the con-
trol part upwards in its casing until it locks
into place (see fig . 1) .
4) Adjust the radio frequency for the trans-
mitter ☞ see chapter 5 .1 . Switch on the
8
receiver and set it to the same frequency
☞
ceiver .
Switch on the audio unit (mixer or ampli-
fier) connected to the receiver .
5) Speak / sing into the microphone . The vol-
ume level can be readjusted by changing
the sensitivity via the control GAIN (10) .
Use the supplied adjusting key for turning
the control .
Adjust the transmitter to an optimum
level . If the level is too high, the transmit-
ter will dis tort; in this case, turn back the
control (if required, even to the left stop) .
If the level is too low, a poor signal-noise
ratio will result; in this case, advance the
control correspond ingly .
6) The transmitter can be locked to prevent
accidental change of frequency or acciden-
tal switching off
7) After all adjustments have been made, un-
lock the control part and slide it back to its
previous position until it locks into place .
8) Use the clip (9) to attach the transmitter to
your clothing, e . g . belt or waistband .
To modify the position of the transmit-
ter on your clothing, the clip can also be
mount ed in a different way: Unscrew the
clip, turn it (clockwise or counter-clockwise
by 90° or by 180°), then retighten it .
9) To switch off the transmitter after opera-
tion, set the power switch (2) to OFF . The
display shortly indicates
tinguishes completely .
5.1 Adjusting the
transmission frequency
1) Keep the key SET (7) pressed for 2 s . The
display shortly indicates
returns to its previous indication . MHZ
discharged
flashes on the display .
Note: To exit the adjusting mode without mak-
ing an adjustment, press the key SET repeatedly
until the display shows
turns to normal operation .
2) Adjust the frequency with the cursor keys:
each time the key
see operating instructions of the re-
☞ chapter 5 .2 .
(6) is pressed, it de-

and then ex-
and then
. Then the unit re-