Publicité

Liens rapides

Installation Instructions for Appleton™ Industrial Areamaster™ High Lumen
LED Luminaire - Yoke Mount
FOR PROPER AND SAFE INSTALLATION OF THIS PRODUCT, PLEASE READ THE FOLLOWING INSTRUCTIONS.
Product Safety
Signal Words Defined
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING indicates a hazardous
situation which, if not avoided, could result in death or serious injury. CAUTION indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury. NOTICE is used to address practices not related to physical injury.
Safety Instructions
WARNING:
• Do not open or remove luminaire with the circuit energized.
• Do not remove or replace fuse when luminaire is energized.
• Do not use this luminaire on ungrounded systems. Failure to ground this luminaire can result in an electric shock, which may be fatal.
• Do not use on ungrounded 480 Volt circuits.
CAUTION:
• Do not look directly at the LEDs when energized.
• Risk of fire.
NOTICE:
• Do not touch the LEDs; touching could leave oily deposits, causing hot spots and potential premature failure.
• This product must be installed in accordance with the applicable installation code by a person familiar with the construction and
operation of the product and the hazards involved.
• This luminaire is designed for and should be installed in accordance with the National Electrical Code
and all applicable local codes.
Marine Locations
CAUTION/ATTENTION:
• Make sure to tighten unused close-up plug to 400 in.-lb. after applying TLNC4 grease. TLNC4 grease shall be applied in 3 lines,
spaced approximately 120 degrees apart, perpendicular to the threads.
• Where flexible cord is used, it should be approved for extra hard, wet location usage and shall have a separate ground conductor.
Agency Ratings
• Wet Locations
• Marine Outside Type (Salt Water) (For installation in USA only)
• Type 3R, 4, & 4X
• IP66 & IP67
Appleton • 1.800.621.1506 • www.appletonelec.com
650544-000 INSTRUCTION SHEET
/Canadian Electrical Code
®
650544-000 Rev. A 12/16 • Page 1 of 12

Publicité

Table des Matières
loading

Sommaire des Matières pour Emerson Appleton Industrial Areamaster

  • Page 1 650544-000 INSTRUCTION SHEET Installation Instructions for Appleton™ Industrial Areamaster™ High Lumen LED Luminaire - Yoke Mount FOR PROPER AND SAFE INSTALLATION OF THIS PRODUCT, PLEASE READ THE FOLLOWING INSTRUCTIONS. Product Safety Signal Words Defined DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
  • Page 2: Feuille D'instructions

    FEUILLE D’INSTRUCTIONS 650544-000 Instructions d’installation du luminaire à LED Appleton™ Industriel Areamaster™ à lumen élevé – Montage sur étrier POUR UNE INSTALLATION CORRECTE ET EN TOUTE SÉCURITÉ DE CE PRODUIT, VEUILLEZ LIRE LES INSTRUCTIONS SUIVANTES. Sécurité du produit Définitions des termes d’avertissement DANGER indique une situation dangereuse qui, si elle n’est pas évitée, entraînera des blessures graves, voire mortelles.
  • Page 3: Dimensions

    Dimensions 5.05” 12.94” 6.16” SQUARE CARRÉ DE 156,5 mm 13.84” 16.28” (4) YOKE BOLTS (4) BOULONS D’ÉTRIER YOKE ÉTRIER 6.00” 2.25” COUNDUIT ENTRY ENTRÉE DE CÂBLE 6.0” TURNING RADIUS 180° ROTATION RAYON DE GIRATION DE 152 MM ROTATION DE 180° 1.75”...
  • Page 4 Mounting Options | Options de montage Yoke Mounting | Montage sur étrier The Areamaster High Lumen LED luminaire with yoke (supplied) will mount directly onto flat surfaces. The yoke has a center clearance hole for a 1/2 inch bolt and two 1/2 inch clearance holes spaced 3-1/2 inches apart on the yoke center line. See Figure 2. Le luminaire Areamaster à...
  • Page 5 Mounting with Optional Crossarm Mounting Bracket | Montage avec support de montage sur traverse en option 0.78” DIA. HOLE R 1.50” TROU DE 19,8 MM DE DIAMÈTRE R 38,1 MM 4.44” 112,8 MM 3.50” 2.31” (2) MOUNTING BOLTS 88,9 MM 58,7 MM (2) BOULONS DE FIXATION Figure 4: Crossarm Mounting Bracket (P/N: G-AM-8-CA) | Support de montage sur traverse (réf. : G-AM-8-CA)
  • Page 6 Mounting with Optional Crossarm Mounting Bracket & Optional Pipe/Wall Mount Bracket | Montage avec support de montage avec traverse en option et support de montage sur paroi/sur tube en option 5.00” 127,0 MM 3/4” BOLT 4.88” BOULON DE 3/4 PO (19 MM) 123,9 MM 3/8”...
  • Page 7 Mounting with Optional Poletop Slip-Fitter | Montage avec embout de poteau en option 3.63” 92,2 MM PRESSURE PLATE AND CORD GRIP ASSEMBLY PLAQUE DE PRESSION ET RÉDUCTEUR DE TENSION MOUNTING BOLT BOULON DE FIXATION 4.58” 116,3 MM 2.00” 50,8 MM (3) LOCKING BOLTS 2.88”...
  • Page 8 Mounting with Optional Poletop Slip-Fitters | Montage avec embouts de poteau en option 3.50" FOR VERTICAL OR HORIZONTAL MOUNT 88,9MM POUR LE MONTAGE VERTICAL OU HORIZONTAL (2) LUMINAIRE MOUNTING BOLTS (2) BOULONS DE FIXATION LUMINAIRE PRESSURE PLATE AND CORD GRIP ASSEMBLY PLAQUE DE PRESSION ET ATTACHES DE CÂBLES 6.00”...
  • Page 9 Wiring | Câblage WARNING: The luminaire must be grounded as required by the National Electrical Code (Paragraph 410-21 and Article 250) or Canadian Electrical Code (Rule 30-500 and Section 10). Verify that ground continuity has been established by using an Ohm meter or other suitable testing equipment before energizing the luminaire.
  • Page 10 6. Close all unused conduit entries with close-up plug (1 supplied). Make sure to tighten unused close-up plug to 400 in.-lb. after applying TLNC4 grease. TLNC4 grease shall be applied in 3 lines, spaced approximately 120 degrees apart, perpendicular to the threads.
  • Page 11: Fuse Replacement

    While every precaution has been taken to ensure accuracy and completeness in this manual, Appleton Grp, LLC. assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Specifications are subject to change without notice. The Appleton and Emerson logos are registered in the U.S. Patent and Trademark Office. All other product or service names are the property of their registered owners.
  • Page 12: Remplacement Du Fusible

    Bien que toutes les précautions possibles aient été prises pour garantir l’exactitude et l’exhaustivité de ce manuel, Appleton Grp, LLC. décline toute responsabilité quant aux dommages résultant de l’utilisation de ces informations ou aux erreurs ou omissions éventuelles. Les spécifications sont sujettes à modification sans préavis. Les logos Appleton et Emerson sont déposés auprès du bureau des brevets et des marques déposées des États-Unis (U.S. Patent and Trademark Office).

Table des Matières