Emerson Appleton AA-51 LED Serie Mode D'emploi
Emerson Appleton AA-51 LED Serie Mode D'emploi

Emerson Appleton AA-51 LED Serie Mode D'emploi

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Installation and Maintenance Instructions for the
Appleton™ AA-51 LED Series Lighting Fixture
FOR PROPER AND SAFE INSTALLATION OF THIS PRODUCT PLEASE READ THE FOLLOWING INSTRUCTIONS
AND KEEP THIS MANUAL FOR FUTURE REFERENCE.
AA-51 LED Series lighting fixtures
for Hazardous Location
Class I, Div. 1, Groups A, B, C, D
Suitable for Group A, when used with Pendant Mount Only
Class II, Div. 1, Groups F and G
Class III
WARNING GENERAL
1. DO NOT MODIFY UNIT IN ANY WAY. Modification
may affect safety and reliability.
2. Improper use or failure to follow these instructions
could result in serious injury or property damage.
3. Operator should be instructed in the safe and
proper usage and maintenance of this product.
WARNING ELECTRICAL
1. Disconnect electrical power before installation,
adjustment and maintenance.
2. DO NOT overload; the amperage and voltage indicated
on the nameplate must not be exceeded.
3. Check continuity before connecting electrical power.
4. All installations must comply with applicable local
and/or National Electrical Code
5. Before installing check fixture unit nameplate and
carton labels to be sure you have correct fixture and
mounting hood. Circuit must be deactivated before
installing fixture.
CAUTION GENERAL
1. All AA-51 LED Series Fixtures are to be mounted
vertically with globe facing down.
The
fixture unit MUST BE installed with one of the
following mounting hoods for safe operation. Failure to
use fixture unit with one of the following mounting hoods
voids warranty as well as the UL Listing and creates the
risk of fire or explosion.
FIGURE 1
The AA-51 fixture MUST BE installed with:
IMPORTANT: Remove all unused conduit plugs
and reinstall with pipe sealant.
Appleton • 1.800.621.1506 • www.appletonelec.com
®
.
AAP-50, AAP-75,
AEP-50, AEP-75
Pendant Hood - ONLY
*Group A with this hood.
(One hub, rigid or flexible mounting)
AAC-50, AAC-75,
AEC-50, AEC-75
Ceiling Hood
(Four hubs, three close-up plugs)
AASB-50, AASB-75,
AESB-50, AESB-75
Short Wall Bracket Hood
(Two hubs, one close-up plug)
INSTRUCTION SHEET
FIXTURE INSTALLATION INSTRUCTIONS
Use the installation drawing as a guide. Install mounting
hood first as all wiring connections are made in the
mounting hood. The fixture unit requires no inter nal
wiring connections.
1. Remove the connection block (VPT-7) from the
mounting hood by loosening (but not removing) the two
Phillips head screws. Turn connection block
counter-clockwise to remove.
2. When using ceiling (AAC- ) or short bracket (AASB-),
mounting hoods, threaded adapter (59064050000) can
be removed by lifting gasket (59064034000) to access
set screw.
• Loosen set screw and turn adapter
counter-clockwise for easier access to junction box.
3. Install mounting hood to conduit system (and/or
wall or ceiling). If using pendant, secure the hood to
the conduit system with the set screw.
4. Pull supply wires from the conduit into the junction box.
• Use supply wire rated 110°C minimum.
5. Secure threaded adapter (where applicable) to junction
box and tighten all set screws. Make connection of
supply wires to the VPT-7 connection block by
attaching "HOT" voltage lead to the black wire and
common "neutral" lead to the white wire on the
connection block.
6. Secure VPT-7 connection block to threaded adapter or
mounting hood by slipping over Phillips head screws;
turning clockwise and tightening screws.
7. Inspect threads of mounting hoods and of the fixture
unit to be sure they are clean and free of damage.
Inspect globe for any chips, scratches or cracks.
CAUTION GENERAL
Chipped, scratched or cracked
globes will fail. Replace any
such defective lamp housing.
8. Thread the fixture unit into mating threads of mounting
hood until tight against gasket of mounting hood.
Locking spring of fixture unit should engage with
notches on mounting hood.
9. Install guard and/or reflector if desired. Check tightness
of set screws and all threaded joints. Activate supply
circuit to test fixture.
650592-000 Rev. B 07/17/18 • Page 1 of 8
650592-000
MUST BE
FREE OF
CHIPS OR
CRACKS

Publicité

Table des Matières
loading

Sommaire des Matières pour Emerson Appleton AA-51 LED Serie

  • Page 1 650592-000 INSTRUCTION SHEET Installation and Maintenance Instructions for the Appleton™ AA-51 LED Series Lighting Fixture FOR PROPER AND SAFE INSTALLATION OF THIS PRODUCT PLEASE READ THE FOLLOWING INSTRUCTIONS AND KEEP THIS MANUAL FOR FUTURE REFERENCE. AA-51 LED Series lighting fixtures FIXTURE INSTALLATION INSTRUCTIONS for Hazardous Location Use the installation drawing as a guide.
  • Page 2 NOTE: All installations must comply with applicable local and/or National Electrical Code. CAUTION: Disconnect supply circuit before opening or relamping fixture. CAUTION: All AA-51 LED series fixtures are to be mounted vertically with globe facing down. MAINTENANCE DATA • To maintain maximum light output from this fixture, it should be cleaned periodically as follows: 1.
  • Page 3 SHORT BRACKET INSTALLATION 1. Remove threaded adapter from junction box for easier access to conduit system. 2. Remove VPT-7 Connection Block from threaded adapter.Pull supply wire (110°C minimum) into junction box. 3. Replace threaded adapter and secure set screw. 4. Connect supply wires to appropriate “black” wire and “white”...
  • Page 4 While every precaution has been taken to ensure accuracy and completeness in this manual, Appleton Grp, LLC. assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Specifications are subject to change without notice. The Appleton and Emerson logos are registered in the U.S. Patent and Trademark Office. All other product or service names are the property of their registered owners.
  • Page 5: Fiche D'instructions

    650592-000 FICHE D’INSTRUCTIONS Instructions d’installation et de maintenance du luminaire Appleton™ série AA-51 LED POUR UNE INSTALLATION CORRECTE ET EN TOUTE SÉCURITÉ DE CE PRODUIT, VEUILLEZ LIRE LES INSTRUCTIONS SUIVANTES ET CONSERVER CE MANUEL POUR RÉFÉRENCE ULTÉRIEURE. INSTRUCTIONS D’INSTALLATION DU Luminaire de la série AA-51 LED pour zone dangereuse Classe I, Division 1, Groupes A, B, C, D LUMINAIRE...
  • Page 6: Instruction Sheet

    0000000000 REMARQUE : toutes les installations doivent respecter le code local et/ou le code national de l’électricité. INSTRUCTION SHEET AVERTISSEMENT : débrancher le circuit d’alimentation avant d’ouvrir ou de remplacer la lampe du luminaire. AVERTISSEMENT : tous les luminaires de la série AA-51 LED doivent être montés verticalement avec le globe ori- enté...
  • Page 7 INSTALLATION AVEC UN SUPPORT COURT 1. Retirer l’adaptateur fileté de la boîte de jonction pour faciliter l’accès au système de conduite. 2. Retirer le bloc de connexion VPT-7 de l’adaptateur fileté. Insérer un câble d’alimentation (classé pour 110 °C au minimum) dans la boîte de jonction. 3.
  • Page 8: Organigramme De La Famille De Luminaires Aa-51 Des Groupes A Et B

    Les logos Appleton et Emerson sont déposés auprès du bureau des brevets et des marques déposées des États-Unis (U.S. Patent and Trademark Office). Tous les autres noms de produits ou de services appartiennent à leurs propriétaires respectifs.

Table des Matières