Additional Specific Safety Rules - Delta 23-710 Manuel D'utilisation

ADDITIONAL SPECIFIC SAFETY RULES

DO NOT OPERATE THIS MACHINE until it is
1.
completely assembled and installed according to the
instructions. A machine incorrectly assembled can
cause serious injury.
OBTAIN ADVICE from your supervisor, instructor, or
2.
another qualified person if you are not thoroughly fa-
miliar with the operation of this machine. Knowledge
is safety.
FOLLOW ALL WIRINg CODES and recommended
3.
electrical connections to prevent shock or electrocu-
tion.
ALWAYS USE THE PROVIDED BLOTTER AND
4.
WHEEL FLANgES to mount the grinding wheels on
the grinder shaft to prevent wheel damge or acciden-
tal separation. Separation can result in fragments fly-
ing off the wheel at high speeds.
5. USE ONLY WHEELS suitable for the speed of the
machine. Unsuitable grinding wheels can come
apart, throwing fragments out at high speeds.
6. USE ONLY WHEELS that have a bore exactly equal
to the arbors of the machine. Never attempt to ma-
chine an undersized wheel to fit an arbor. Unsuitable
grinding wheels can come apart, throwing fragments
out at high speeds.
7. DO NOT OVERTIgHTEN WHEEL NUT.
8. DO NOT USE A WHEEL THAT VIBRATES. Dress
the grinding wheel, replace it, or replace the bearings
of the shaft. Unsuitable grinding wheels can come
apart, throwing fragments at high speeds.
9. INSPECT WHEELS before starting the machine
for cracks or fragments. REPLACE DAMAgED
WHEELS immediately. Parts of the wheel can be
thrown at high speeds causing serious injury.
10. ADJUST EYE SHIELDS close to the grinding wheel,
and re-adjust as the wheel wears down. Flying sparks
are dangerous and can cause fires or explosions.
11. ALWAYS MAkE SURE the eye shields are in place,
properly adjusted, and secured.
12. ADJUST TOOL RESTS close to the grinding wheel
(1/8" separation or less). Tighten the tool rest secure-
ly to prevent shifting positions, and re-adjust as the
wheel wears down. The workpiece can be drawn into
the wheel, causing damage to the workpiece and/or
serious injury.
13. STAND TO ONE SIDE before turning the machine
"ON". Loose fragments or wheel parts could fly from
the wheel at high speeds.
14. NEVER gRIND ON A COLD WHEEL. Run the grind-
er for one full minute before applying the workpiece.
A cold wheel has a tendency to chip. Those frag-
ments could fly from the wheel at high speeds.
15. NEVER START THE MACHINE with the workpiece
against the grinding wheel. The workpiece can be
drawn into the wheel, causing damage to the ma-
chine and/or serious injury.
16. CLEAN THE MACHINE thoroughly when processing
Refer to them often and use them to instruct others.
All manuals and user guides at all-guides.com
Failure to follow these rules may result in serious personal injury.
SAVE THESE INSTRUCTIONS.
different types of workpieces (wood, steel, or alumi-
num). Combining wood and metal dust can create
an explosion or fire hazard. DO NOT gRIND OR
POLISH MAgNESIUM. Fire will result.
17. NEVER gRIND NEAR FLAMMABLE gAS OR LIQ-
UIDS. Sparks can create a fire or an explosion.
18. AVOID AWkWARD OPERATIONS AND HAND PO-
SITIONS. A sudden slip could cause a hand to move
into the grinding wheel.
19. kEEP ARMS, HANDS, AND FINgERS away from
the wheel. The abrasive surfaces can cause serious
injury.
20. HOLD THE WORkPIECE FIRMLY against the tool
rest. Loss of control of the workpiece can cause seri-
ous injury.
21. DRESS THE WHEEL on the face only. Dressing the
side of the wheel could cause it to become too thin
for safe use.
22. gRIND A WORkPIECE using the face of the grind-
ing wheel only. Loss of control of the workpiece can
cause serious injury.
23. NEVER APPLY COOLANT directly to the grinding
wheel. Coolant can weaken the bonding strength of
the grinding wheel and cause it to fail. Dip the work-
piece in water to cool it.
24. DO NOT TOUCH the ground portion of a workpiece
until it has cooled sufficiently. Grinding creates heat.
25. PROPERLY SUPPORT LONg OR WIDE WORk-
PIECES. Loss of control of the workpiece can cause
serious injury.
26. NEVER PERFORM LAYOUT, ASSEMBLY, or set-
up work on the table/work area when the machine is
running. A sudden slip could cause a hand to move
into the wheel. Severe injury can result.
27. TURN THE MACHINE "OFF", disconnect the ma-
chine from the power source, and clean the table/
work area before leaving the machine. LOCk THE
SWITCH IN THE "OFF" POSITION to prevent un-
authorized use. Someone else might accidentally
start the machine and cause serious injury to them-
selves.
28. ADDITIONAL INFORMATION regarding the safe
and proper operation of power tools (i.e. a safety
video) is available from the Power Tool Institute, 1300
Sumner Avenue, Cleveland, OH 44115-2851 (www.
powertoolinstitute.com). Information is also avail-
able from the National Safety Council, 1121 Spring
Lake Drive, Itasca, IL 60143-3201. Please refer to
the American National Standards Institute ANSI 01.1
Safety Requirements for Woodworking Machines
and the U.S. Department of Labor OSHA 1910.213
Regulations.
4