Clarity EXL30 Guide De L'utilisateur page 5

UK
The telephone is ready to use.
DESKTOP
Fig. D Connect the Telephone Line Cable and the Handset Cable to the telephone.
If required, use the supplied adapter.
Lift the handset and listen for a dial tone.The telephone is ready to use.
USING YOUR EXL30
INCOMING VOICE AMPLIFICATION
Fig. E Lift the handset and press the Amplify Button (13) to turn on the amplifier.
Fig. F You can adjust the volume of incoming calls by sliding the Volume Control (10).
The amplifier will turn off when you hang up.
CAUTION: Operation of the Amplification feature will make the receiver very loud. It is
designed specifically for hearing impaired users.
Amplification can be activated by pressing the Amplify Button (13) the Amplify Indicator (14)
indicates that Amplification is in operation.
By activating the Amplification feature you are choosing to increase the level of amplification that
allows any abnormal event to exceed 118dB.This is potentially harmful.The volume control
should be increased gradually to find the minimum level of amplification that is comfortable for
you. Avoid prolonged or unnecessary exposure to high volume levels
INCOMING VOICE TONE
The EXL30 provides extra amplification at the sound frequency you need to boost.To identify
the sound frequency range that best suits your needs, follow these steps:
Lift handset and listen for a dial tone.
Press the Amplify Button (13) to turn on the amplifier (refer to Fig. I on page 5).
Fig. G Slide the Tone Control (17) either right or left for maximum clarity.
The next time and every time you press the the Amplify Button (13), your EXL30 will
give you the best listening clarity.
RINGER VOLUME AND TONE
You can adjust the Ringer Volume Switch (5) as high as 85+ decibels.The settings available are
OFF, LO and HI, as shown in the main diagram on page 3.The Ring Tone Switch (4) has two pitch
settings: LO and HI, as shown in the main diagram on page 3.
HOLD
Fig. H To put the call on hold, press the Call Hold Button (18) and return the handset to its
cradle.You will notice the Call Hold Indicator (16) illuminates.
NOTE: If you pick up an extension phone on the same line when the EXL30 is on HOLD,
the EXL30 will release the HOLD and you can continue your conversation on the extension
telephone.
9
LAST NUMBER REDIAL
Fig. I To redial the last number called, lift the handset and press the Redial Button (8).The
telephone will redial up to 31 digits.
FLASH/RECALL
Fig. J Press the Flash/Recall Button (9) to access special services available from your local
telephone company e.g. Call Waiting and 3-Way Calling.
(Subject to your local telephone service).
PROGRAMMING THE MEMORY BUTTONS
Fig. K You can automatically dial twelve programmed telephone numbers using the Memory
Buttons (7). Each button can be programmed (or reprogrammed using the same
procedure) for a telephone number up to 15 digits long.
Fig. L To program a button, follow these steps:
Lift the handset and press the Programme Button (15).
Fig. M Enter the phone number on the keypad just as you would dial it normally.
Press Redial Button (8) if you want to insert a brief pause between two numbers.
Press a Memory Button (7) to store this number on that button.
Immediately hang up the handset.
NOTE: Any number previously stored at that button will be overwritten.
To change a stored number, repeat the programming process starting with Fig. K.
NOTE: Do not programme emergency service numbers into any memory button.
DIRECT AUDIO OUTPUT
Fig. N The Audio Output Socket (2) allows you to connect the EXL30 to a hearing aid, neck
loop, cochlear implant or other assistive listening devices.
To use this port, plug in a compatible auxiliary cable and connect it to your assistive
listening device.
Speak into the handset when you use the Audio Output connection.
NOTE: This port is a TNV connection with respect to EN41003. Only connect equipment that
complies with EN60950 to this port.
UK
10