Panasonic WV-CU161 Mode D'emploi page 18

• For using alarm input terminals 1-4
ALARM DISPLAY ON
SITE ALARM
TERM.ALARM
ALARM OUTPUT
ALARM BUZZER
ALARM TERMINAL
(1) Alarm Display Setting
This item lets you select whether or not the message
ALARM on the monitor when the alarm is activated.
1. Display the ALARM SETUP menu.
2. Select ALARM DISPLAY by moving the joystick up or
down.
3. To have ALARM displayed, select ON for the ALARM
DISPLAY parameter. Otherwise select OFF by moving
the joystick to the right or left.
The initial factory setting is ON.
Note: The display time differs depending on (4) Alarm
Output Setting.
(2) Site Alarm Setting
This item lets you enable or disable the camera site alarm.
1. Display the ALARM SETUP menu.
2. Select SITE ALARM by moving the joystick up or down.
3. Select SITE ALARM ON or OFF by moving the joystick
to the right or left.
The initial factory setting is ON.
(3) Terminal Alarm Setting
This item lets you enable or disable the alarm signal from
the alarm connector.
1. Display the ALARM SETUP menu.
2. Select TERM.ALARM by moving the joystick up or
down.
3. Select TERM.ALARM ON or OFF by moving the joystick
to the right or left.
The initial factory setting is ON.
(4) Alarm Output Setting
This item lets you select an alarm operation duration when
the alarm is activated.
It determines the following. (The selected duration applies
to each alarm operation.)
• The length of time that ALARM is displayed on the mon-
itor (ALARM DISPLAY ON mode).
• The length of time the alarm is output to external
devices (from the ALARM OUTPUT connector).
• The length of time the buzzer sounds (ALARM BUZZER
ON mode).
1. Display the ALARM SETUP menu.
2. Select ALARM OUTPUT by moving the joystick up or
down.
18
All manuals and user guides at all-guides.com
ALARM SETUP
ON
ON
10S
ON
3. Select the desired alarm output duration, 1S-30S, 40S
50S 1MIN 2MIN, 3MIN, 4MIN, 5MIN EXT, or OFF by
moving the joystick to the right or left.
The initial factory setting is 10S.
EXT: The alarm signal continues to be output from the
alarm output connector till the alarm is reset. The
alarm is not automatically reset.
1S-5MIN: The alarm signal is supplied from the alarm
output connector only for the set time. The alarm is
automatically reset after the set time. (The ALARM
indicator changes from blinking to steady light.)
OFF: No alarm output signal is supplied. (The alarm is
deactivated.)
(5) Alarm Buzzer Setting
This item lets you select whether or not the alarm buzzer
sounds when the alarm is activated.
1. Display the ALARM SETUP menu.
2. Select ALARM BUZZER by moving the joystick up or
down.
3. Select ALARM BUZZER ON or OFF by moving the joy-
stick to the right or left.
The initial factory setting is ON.
Note: The alarm buzzer time differs depending on (4) alarm
output setting.
(6) Alarm Preset Setting
This item lets you select picture preset numbers in preset-
ting combination camera positions when the alarm is acti-
vated.
• For using alarm input/output terminal and alarm recover
input/output terminal.
ALARM SETUP
ALARM DISPLAY ON
SITE ALARM
TERM.ALARM
ALARM OUTPUT
ALARM BUZZER
ALARM PRESET
1. Display the ALARM SETUP menu.
2. Select ALARM PRESET by moving the joystick up or
down.
3. Move the joystick to the right or left to select the
desired preset numbers of the picture on the moni-
tor in the range of 1-64 or [–] if no preset numbers
are assigned.
The initial factory setting is – (No assignment).
1-64: Preset numbers
–: No assignment
Note: ALARM PRESET is available only when a
combination camera is connected.
ON
ON
10S
ON
–