Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
User Manual
Introduction
Thank you for purchasing the LINDY Fibre Optic DVI-D Dual Link Extender!
This Fibre Optic Extender allows you to transmit DVI-D Dual Link signals up to maximum
resolution of 2560x1600 at distances of up to 500m/1600 feet using an 8 core MPO multimode
fibre cable. This cable is available upon request from LINDY in custom made lengths.
Features
•
Extends DVI-D signals up to 500m/ 1600 feet
•
Suitable for use with Computer, Video Wall and Home Theatre equipment
•
Uses a standard MPO fibre cable (not included)
•
Auto power save mode
•
Auto EDID programming and Self-EDID learning feature
•
Auto Laser disable if DVI cable is removed
Specification
•
DVI 2.0 Compatible
•
Supports DVI-D Dual Link, resolutions up to 2560x1600@60Hz
•
No HDTV / HDCP support
Package Contents
LINDY Fibre Optic DVI-D Dual Link Extender: 1x Transmitter, 1x Receiver
Multi-Country Power Adapter (5VDC) x 2
This User Manual
Pre-Installation Remarks
The Extender will get warm up to 45 °C during operation!
Avoid touching it directly and install it with adequate ventilation!
Self-EDID learning procedure
The Fibre Optic DVI-D Extender has a default EDID preset table stored in the TX. If the display
resolution does meet this default EDID stored in transmitter module, you have to perform the
following EDID self-learning procedure.
The EDID of a display can be stored in the TX by plugging it into the display.
1. Connect the power supply to the transmitter module (TX)
2. Switch on the monitor and connect the TX to the monitor
All manuals and user guides at all-guides.com
CAUTION!
3
English
User Manual
3. Press the Self-EDID button with a narrow pin or paper clip
4. When the green LED stops flashing, disconnect the TX and install it in your regular
extender installation
Recovery of original EDID setting
Plug the power adapter into the transmitter and disconnect all other connectors. Push the self-
EDID button with a narrow pin. When the green EDID LED is totally turned off, the
recovery procedure is completed.
Installation
Do NOT introduce strain or stress to the fibre optic MPO cable and connectors!
Do NOT bend the fibre cable below the minimum allowed radius, approximately 10cm -
Important! Before starting the installation, please ensure that all devices are powered off.
1. Connect the power supply to both the transmitter (TX) and receiver (RX). Ensure the green
power LEDs near the DC connector are turned on (green)
Transmitter: If the graphics source can provide enough power to the TX via the DVI
connector the transmitter's power supply is not required. In this case make sure the green
power LED is illuminated brightly. A dim LED indicates insufficient power from the DVI port.
2. Connect the TX and RX to your DVI devices. A short DVI-D extension cable (maximum
length 2m) or 90 degree angled adapter may be used if required.
3. Remove the dust covers from TX and RX MPO ports and from your MPO Cable and
connect it to TX and RX. Make sure not to introduce dust or scratches to the surfaces!
4. Please make sure that the MPO connectors are fully engaged and then power on your
display and source to complete the installation.
5. If you can't get the proper resolution on the display, please go through the Self-EDID
programming procedure above and repeat the installation procedure again.
Troubleshooting Tips
If you cannot adjust the correct resolution of your monitor please follow the steps of Self-EDID
learning procedure.
If you cannot solve the problems contact your dealer or LINDY Tech Support. Find worldwide
LINDY contact information at www.lindy.com
see fiber cable supplier's specification!
4
English
Publicité
Table des Matières
