Gemini CDJ-505 Manuel D'instructions page 5

FUNCTIONS:
(CONTINUED)
BPM: Press and hold the BPM button to turn on the BPM read out, once
12
on you may TAP the button to the beat of the music, after a few TAPS
the display will read out the average BEATS PER MINUTE of the track.
PGM: Allows you to create a set playlist. To program a set list into the
13
CDJ-505 memory, begin by stopping the unit from play and pressing
PGM to begin the set list. Select a track by using the track selection but-
ton to scan to the first track to be placed in the set list.
When you have selected the proper track press PGM and the
CDJ-505 will be ready to set your next selection. Repeat the previous
steps until you have completed your playlist, then press play to begin
the set list.
PITCH: Pushing and holding the PITCH button (the button will light up)
14
activates the PITCH CONTROL SLIDE. You can then select which PITCH
percent you want by pressing the PITCH button and choosing either +/-
8%, 12% and 24% depending on which LED is illuminated. Push and
hold the PITCH button again to deactivate this mode.
PITCH CONTROL SLIDE: Moving the PITCH CONTROL SLIDE
15
up or down will lower or raise the pitch percentage up to + or - 24%
depending on the PITCH BUTTON setting.
PITCH BEND: Pushing the PITCH BEND BUTTONS will automatically
16
bend the pitch up to +26% or bend the pitch down to -26% depending
on the setting of the PITCH BUTTON. Releasing the buttons will return
the pitch to the original pitch setting. You can use this function to match
the beat when mixing from one song to another.
LOOP SECTION: A LOOP repeats the section between the entry point
17
(IN) and the exit point (OUT). To set a loop while the unit is playing,
start by pressing the IN BUTTON (it will light up) and when you reach
the desired end loop point press the OUT BUTTON (it will also light up).
The loop will continue playing until you press the OUT BUTTON again
allowing the music to continue from that point on, to re-engage the loop
you must press the RELOOP BUTTON. When you have released your
loop the OUT BUTTON will turn OFF and the IN BUTTON will remain lit
to indicate that your loop is stored in the CDJ-505 memory. Pressing the
IN BUTTON again while the unit is playing will erase the previously
saved loop while saving your new loop entry point. Press OUT to exit
the loop and save a new complete loop.Press RELOOP to return to the
beginning of the previously saved loop from normal play. Press
RELOOP repeatedly to cause the loop to stutter.
NOTE: THE FIRST LOOP WILL HAVE A PAUSE AT THE EXIT POINT,
WHILE ALL OTHERS WILL BE SEAMLESS.
PLAY/PAUSE: Each press of the PLAY/PAUSE BUTTON
18
causes the operation to change from PLAY to PAUSE or from PAUSE
back to PLAY. The PLAY/PAUSE BUTTON remains lit when in PLAY
mode, while it blinks in PAUSE mode.
CUE: While the unit is playing and after the cue point has been
19
programmed, pressing CUE will cause the CD player to enter the
PAUSE mode (PLAY/PAUSE BUTTON blinks) at the programmed cue
point (the CUE LED is lit). Holding down the CUE button
changes the function to preview , and allows you to stutter start or play
from the programmed CUE POINT Releasing the CUE button will return
the CD to the preset CUE point.
REPEAT: Press the repeat button once to engage (1) or repeat the
20
selected track. Press REPEAT again to engage ALL setting which will
repeat all the tracks on the CD. Press REPEAT again to disengage the
repeat function.
USB PORT The USB port allows the connection of any USB mass stor-
21
age device*.
USB/CD SELECT BUTTON The USB/CD select button allows you to
22
toggle from the CDJ-505 internal CD drive and the mass storage de-
vice connected to the USB port.
TRACK SELECTION ROTARY: The TRACK SELECTION ROTARY
23
allows you to navigate through folders or search through tracks
depending on weather you are in USB mode or CD mode.
In CD mode the rotary can search through cd tracks, turning the
rotary to the right or clock-wise advances the selection, and turning
the rotary to the left or counterclock-wise decreases the selection.
Once you have found your selection you can load it for play by
pressing the ROTARY knob to confirm your selection.
In USB mode the ROTARY knob allows you to search through folders
and navigate through music libraries on your USB device, Simply ro-
tate the rotary until you find the desired folder and push the rotary
in to choose that folder, continue to search in this manner until you
find the desired track, then just like in CD mode press the rotary
again to load and play the desired track.
NOTE : ONCE YOU HAVE SKIPPED TO ANOTHER TRACK, YOU MAY NOT GO BACK TO YOUR PROGRAMMED CUE POINT.
YOU MUST BEGIN YOUR CUE SELECTION OVER AGAIN, THE CUE WILL BE PRESET TO THE BEGINNING OF THE NEWLY
SELECTED TRACK.
We recommend that you use a MASS STORAGE DEVICE that is no
*
larger than 2 gb and that only has less than 100 folders with less
than 1000 songs in any one folder. larger drives will work but they
will greatly affect the time in which it takes to search and or load a
song.
SPECIFICATIONS:
GENERAL:
Type.........................................Compact Disc Player & USB Mp3 Reader
Disc Type...................................Standard Compact discs (12 cm & 8 cm)
Time Display....................Track Elapsed, Track Remain, or Total remain
Variable Pitch.......................................± 24% Slider with Resume Switch
Pitch Bend............................................................................± 26% Maximum
Instant Start....................................................................Within 0.03 seconds
Installation..........................................................................................Table top
Dimensions:..................................................................11.0" x 3.5" x 11.75"
..............................................................(279.4 mm x 88.9 mm x 298.4 mm)
Weight Per Unit...............................................................5.78 lbs. (2.62 kg)
AUDIO SECTION:
Quantization......................................1 Bit Linear/Channel, 3 Beam Laser
Oversampling Rate..............................................................................8 Times
Sampling Frequency.........................................................................44.1 kHz
Frequency Response............................................................20 Hz to 20 kHz
Total Harmonic Distortion...................................................Less Than 0.05%
Signal to Noise Ratio..............................................................................85 dB
Dynamic Range.......................................................................................85 dB
Channel Separation.................................................................85 dB (1 KHz)
Output Level...................................................................2.0 +/- 0.2V R.M.S.
Power Supply......................................................AC 115/230V, 60/50 Hz
SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE WITH-
OUT NOTICE FOR PURPOSE OF IMPROVEMENT.
CDJ-505
5