Télécharger Imprimer la page

R&G RGH0001BK Instructions De Montage page 3

Publicité

Les langues disponibles

Les langues disponibles

Offer the hugger into position.
Place the black button headed bolt through the hole in the side lug of hugger and through the
already positioned new spacer into the swing-arm, do not tighten yet.
Fit the two silver button headed bolts with washers through the holes in the hugger and engage the
threads in the swing-arm, do not tighten yet.
Tighten the two lower bolts until the hugger is only held in position as centrally as possible in
slots.
Refit wheel.
Position the white spacer block included in kit on centre-line of tyre.
Move the hugger so the white spacer block just slides between hugger and tyre (PLEASE NOTE
A MINIMUM OF 14mm RADIAL CLEARANCE IS REQUIRED) while ensuring the sides of
the hugger are equally spaced from the edges of the tyre.
Using a 4mm allen key tighten the two lower bolts.
Tighten the upper bolt to secure hugger in place (do not over-tighten).
 Ensure the hugger has not moved while tightening
Gently ease boot guard portion of the hugger away from swing-arm and peel remaining protective
film from the adhesive tape, and press firmly into position.
Ensure wheel is tightened to 108Nm torque.
Reposition exhaust and secure using original nut, bolt and washers.
Retighten exhaust band bolt to 17Nm.
IMPORTANT: WHEN FITTING THE HUGGER, IT MUST BE POSITIONED AS
DESCRIBED ABOVE SO THAT THE HUGGER WILL NOT CONTACT THE REAR
WHEEL. IT IS YOUR RESPONSIBILITY TO CHECK FOR THIS POSSIBILITY AND TAKE
AVOIDING ACTION. FAILURE TO CHECK THIS COULD RESULT IN SERIOUS INJURY.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The
Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those
in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for
its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify
any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the
motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a
replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise
than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or
neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be
liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or
the fitting or service concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were
purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-
sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value
exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of
discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty
goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
www.rg-racing.com
Email:
info@rg-racing.com

Publicité

loading