Instruction Sheet - Hella DuraLED 2SB 980 606 Serie Guide Rapide

INSTRUCTION SHEET

2SB 980 606-xxx / 2SB 959 060-621 /
for:
HM060621
Lamp Mounting Instruction
Screw Cap Removal
Carefully insert a small flat blade screwdriver between the cap and the lens and pull towards the
lens, the cap will clip off.
To install the cap push in by hand until the top is flush with the lens.
Surface Mounting
• Drill two holes up to 6.5mm Ø at 148mm centres.
• 6mm Ø screws or bolts are recommended to mount the lamp
using the mounting bushes provided.
• Lamp should be mounted on a flat surface.
• If passing the cable through a hole, ensure there are no sharp
edges to cut or chafe the cable.
• Alternatively, cable can be routed through the end of the base.
• Connect cable as per chart below.
• Clip the screw caps on securely until flush with the lamp surface
Note: When mounting lamp units side by side allow a gap of 5mm to ensure screw cap removal.
General Dimensions (in millimetres)
Wiring Colour Coding
Lamp is polarity conscious. The reversal of the polarity will not damage this product but will inhibit its
function.
HELLA recommends wire connections be soldered, and heat shrink tubing applied to seal the joint.
Colour Connect to
White Negative (-)
Red Stop (+)
Brown Rear Position (+)
Blue * Park (+)
* Park function not installed on all models.
NB: Lamp must be protected by a fuse rated at 5 amperes maximum.
Mounting
bush
Cable routing
Note: Bolts not included
Cable exit location
8.2mm
6mm Ø max
Cable exit
cable size
13.6mm
Power Consumption
-
6 watts
2.5 watts
2.5 watts
Important Notes for Installer and
Vehicle Owner
Introduction
LED signal and marker lamps offer many advantages over conventional bulb lamps. Significantly
reduced power consumption, ultra long life and high tolerance to shock and vibration make the LED
lamps the ideal choice for the commercial transport industry, where the cost of ownership versus
the initial purchase price of the product is well understood.
Compatibility to existing electrical systems
It is important for the installer to ascertain the compatibility of the low power consumption LED
lamps with the electrical and/or electronic systems of the complete vehicle, including trailers. In
most cases the reduced power consumption is beneficial by imposing less demands on the entire
electrical system.
For certain functions some electrical systems rely on a set power consumption for monitoring
whether, for example, a trailer is connected.
Electromagnetic Compatibility (EMC)
This LED lamp in an electronic device. The electrical circuits contain components that suppress
possible interference, both emission as well as susceptibility, to the limits prescribed in UNECE
Vehicle Regulation No. 10.
To avoid false signals or interference, it is standard practice that sensitive instrumentation such as
ABS and Tachometers etc. are provided with direct earths.
Protection against damage due to voltage spikes
This LED lamp is protected against damage from positive voltage spikes caused by events such
as load dump conditions up to severity level 3 of ISO 7637-2 and contains a Transient Voltage
Suppressor (TVS) designed to withstand a pulse of up to 5000 Watts.
The lamp is protected against reverse polarity connection and negative voltage spikes of up to
1000 volts.
Electric Welding
Electric Welding may damage the LED lamps. For LED lamps, HELLA recommends the negative
connection to be wired isolated from the vehicle chassis. If the lamp uses the chassis as the earth
return it is recommended that this earth return is disconnected during electric welding.
FIT AND FORGET - BY DESIGN
Congratulations, the product you have selected comes from HELLA - a world leader in LED
lighting design.
Following the launch of the first LED automotive signal lamps in 1990, HELLA Design and
Innovation continues to set new standards. HELLA innovative solutions have been incorporated into
millions of lamps, engineered and tested to the most stringent standards, to suit the most demanding
environmental conditions.
The cornerstone to the success of our products is our no compromise Fit and Forget - by Design philosophy
which is incorporated into every step of the product life cycle.
In a world consuming finite resources at an ever faster rate, Fit and Forget - by Design is the right
environmental choice that also makes perfect economic sense to customers that consider the total life cycle
Cost of Ownership.
For general comments about HELLA's products please contact us on E-mail at techfeedback@hella.co.nz