Additional Refrigerant Charge - Sanyo 3-WAY ECO-i SPW-C0705DZH8 Instructions D'installation

Table 1-6 Indoor Unit Tubing Connection Size ( 1 – 40)
Indoor unit type
Suction tubing (mm)
Distribution joint –
solenoid valve kit Discharge tubing (mm)
tubing
Liquid tubing (mm)
Solenoid valve kit –
Gas tubing (mm)
Indoor unit tubing
Liquid tubing (mm)
connection
*1: For the solenoid valve kits, use type 160 with parallel specifi cations. Branch the tubing before and after the solenoid valve kits.
1-7. Straight Equivalent Length of Joints
Design the tubing system by referring to the following table for the straight equivalent length of joints.
Table 1-7 Straight Equivalent Length of Joints
Gas tubing size (mm)
90° elbow
45° elbow
U-shape tube bent
(R60 − 100 mm)
Trap bend
Y-branch distribution joint
Ball valve for service
Table 1-8 Refrigerant tubing (Existing tubing can be used.)
Tubing size (mm)
Material O
ø6.35 t0.8
ø9.52 t0.8
ø12.7 t0.8
ø15.88 t1.0
ø19.05 t1.0
ø22.22 t1.15

1-8. Additional Refrigerant Charge

Additional refrigerant charge amount is calculated from the liquid tubing total length as follows.
Required amount of additional refrigerant charge = [ (Amount of additional refrigerant charge per meter of each size of liquid tube × its tube
length) + (...) + (...)] + [(Necessary amount of additional refrigerant charge per
*Always charge accurately using a scale for weighing.
Table 1-9-1 Amount of Additional Refrigerant Charge Per Meter, According to Liquid Tubing Size
Liquid tubing size (mm)
Amount of additional
refrigerant charge/m (g/m)
Table 1-9-2 Necessary Amount of Additional Refrigerant Charge Per Outdoor Unit
SPW-C0705DZH8
Table 1-10 Refrigerant Charge Amount at Shipment (for Outdoor Unit)
SPW-C0705DZH8
11.8 kg
7 9 12
ø12.70
ø6.35
12.7 15.88
0.30 0.35
0.23 0.26
0.90 1.05
2.30 2.80
Equivalent length conversion not needed.
Equivalent length conversion not needed.
•
Material 1/2H H
ø25.40 t1.0
ø28.58 t1.0
ø31.75 t1.1
ø38.10 t1.15
ø41.28 t1.20
6.35 9.52 12.7 15.88 19.05 22.22
26 56 128 185
SPW-C0905DZH8
SPW-C0905DZH8
11.8 kg
16 18 25
ø15.88
ø12.70
ø9.52
19.05 22.22 25.4
0.42 0.48 0.52
0.32 0.36 0.39
1.26 1.44 1.56
3.20 3.80 4.30
* When bending the tubes, use a bending radius that is
at least 4 times the outer diameter of the tubes.
In addition, take sufficient care to avoid crushing or
damaging the tubes when bending them.
outdoor
unit + (...) + (...)]
259 366
SPW-C1155DZH8
SPW-C1155DZH8
11.8 kg
10
30 36 48
ø15.88
ø9.52
28.58 31.8
0.57 0.70
0.43 0.53
1.71 2.10
4.70 5.00
SPW-C1305DZH8
3.2 kg
SPW-C1305DZH8
11.8 kg
60 76* 1 96* 1
ø19.05 ø22.22
ø15.88 ø19.05
ø19.05 ø22.22
38.1
0.79
0.59
2.37
5.80
SPW-C1405DZH8
3.2 kg
SPW-C1405DZH8
11.8 kg