Frigidaire FFLE1011MW Guide D'utilisation

CAUTION
EXCESSIVE WEIGHT HAZARD
• Dryer must be properly grounded at all times.
Avoid back or other injury. Use more than one
• Vent dryer through free-fl owing, outdoor-
person to move, lift or tip the appliance.
vented, metal duct system.
ELECTRICAL SHOCK HAZARD
• Improper gas installation or LP conversion
Appliance must be properly grounded at all times.
could result in injury or even death.
UNPACK
CAREFULLY
TIP
B)
A)
IF REMOVED, REINSERT
FOAM SUPPORT AND
RETAPE LID
PROTECT FLOOR
REMOVE & SAVE
3/8" (10 mm)
wrench or socket
C)
RETURN UPRIGHT
AND EMPTY TUB
LEVEL
lower
raise
A)
ADJUST
B)
C)
CHECK STABILITY,
CORNER-TO-CORNER
LEVEL BOTH WAYS
WARNING IMPORTANT
Please read all safety instructions before using your
new laundry center. For best washing results with
your new laundry center, remember to review:
INSTALLATION INSTRUCTIONS
USE & CARE GUIDE
VENT EXHAUST
• USE ONLY 4 INCH (10.2 CM) RIGID METAL
OR SEMI-RIGID METAL DUCTING
• REPLACE PLASTIC OR FOIL DUCTS WITH
METAL
• CLEAN LINT FROM PRESENT DUCT
SYSTEM BEFORE ADDING ON
• SEE CHART TO THE RIGHT FOR
ACCEPTABLE NUMBER OF 90° TURNS IN
SYSTEM
• DO NOT USE SCREWS TO CONNECT DUCTS
• DO NOT USE REGULAR DUCT TAPE TO
CONNECT DUCTS, ONLY METAL FOIL TAPE
• 4" (10.2 cm) CLAMP RECOMMENDED FOR
0
CONNECTION BETWEEN DRYER & EXHAUST
1
SYSTEM
• EXHAUST
2
SYSTEM
3
MUST BE
VENTED
*Do not install plastic or foil ducting. If
OUTSIDE WITH APPROVED VENT HOOD
installing semi-rigid ducting, do not exceed 8 ft
(2.4 m) total duct length.
• FOR INSTALLATION IN A RECESSED
AREA OR CLOSET, SEE COMPLETE
INSTALLATION INSTRUCTIONS
• FOR MOBILE HOME INSTALLATION, SEE
COMPLETE INSTALLATION INSTRUCTIONS
CONNECT
B)
A)
INSERT RUBBER
WASHERS (x4)
DETERMINE
HOT SUPPLY
F)
TIGHTEN G)
ADDITIONAL
2/3 TURN
WITH PLIERS
TURN ON WATER,
CHECK FOR LEAKS
I)
CONNECT POWER
CAUTION
ELECTRICAL SHOCK HAZARD
Do NOT use prong adapter.
Do NOT remove ground prong.
Do NOT use extension cord.
MAXIMUM LENGTH*
of 4" (10.2cm) Rigid Metal Duct
VENT HOOD TYPE
(Preferred)
CORRECT
4" 2.5"
(10.2cm) louvered (6.35cm)
56 ft. (17 m) 42 ft. (13 m)
48 ft. (14.5 m) 34 ft. (10.5 m)
40 ft. (12 m) 26 ft. (8 m)
32 ft. (9.5 m) 18 ft. (5.5 m)
INCORRECT
C)
INSTALL HOT HOSE D)
ON HOT SUPPLY,
COLD HOSE ON COLD TIGHTEN ADDITIONAL
SUPPLY (HAND-TIGHT) 2/3 TURN WITH PLIERS
33" min
(84cm min)
H)
SECURE DRAIN HOSE
WITH SUPPLIED CABLE TIE
J)
NOTE TO REMARQUE POUR
INSTALLER L'INSTALLATEUR
Leave these instructions
Laissez ces instructions au
with the customer. client.
Suite de la version française au verso.
HEAT SOURCE
GAS DRYER G
WRENCH-TIGHT
APPLY APPROVED THREAD
SEALANT.
REFER TO INSTALLATION
MANUAL
INSTRUCTIONS FOR MORE
SHUTOFF
DETAILED INFORMATION.
ELECTRIC DRYER
30 AMP
DON'T
MOVE
U.L.-APPROVED
STRAIN RELIEF
OPERATE
E) HOT FOR DETAILED O FOR DETAILED OPERATING INSTRUCTIONS REFER
TO COMPLETE USE & CARE GUIDE .
INSTALL HOT
Your washer is equipped
HOSE ON HOT
with a safety lid lock. The
INLET, COLD HOSE
washer will not operate
ON COLD INLET
with the lid open.
(HAND-TIGHT)
Push in cycle selector knob
COLD
to begin cycle. You will
hear a beep, the lid will
lock and the cycle will
start. Push in the cycle se-
lector again to pause cycle
or add items. You will hear
two beeps and the cycle
will stop. Wait for the lid to
unlock. DO NOT FORCE
OPEN THE LOCKED LID.
DO NOT OPERATE WASHER IF SAFETY LID LOCK IS
MISSING, DAMAGED OR OPERATING IMPROPERLY.
OPEN GAS VALVE,
CHECK FOR LEAKS
WITH SOAPY WATER
NOTA AL
INSTALADOR
Deje estas instrucciones con
en cliente.
Español continua en la pagina trasera.
L.P. SYSTEMS MUST USE
COVERSION KIT INSTALLED
BY QUALIFIED TECHNICIAN.
30 AMP
WHITE
MOVE GROUND
GREEN
RED OR
RED OR
BLACK
BLACK
INSTALL
SAFETY LID LOCK
TO AVOID SERIOUS PERSONAL INJURY,
CLEAN LINT
FILTER AFTER
EVERY LOAD.