Nordpeis Salzburg M Manuel D'installation page 21

also important to ensure that this plate is level in both
directions before proceeding with the installation.
Attention! The use of shims to level the base plate
is not recommended as the differences in tension
on the base plate can cause it to crack under the
weight of the product.
If a fresh air supply (not included) is connected through
the bottom plate, it is important to make a hole at the
location of the recess which is placed under the base
plate, before it is placed on any added adhesive or
mortar, and to adapt air inlet flue before continuing with
the installation.
Attention! If an air supply set is to be connected to
the fireplace through the base plate, then the hole
in the back surround (FIG 9) must be sealed of on
the inside with the supplied plug before the element
is lowered over the inner core.
FIG 4-7:
Place the first PowerStone bottomplate (2) in the centre
of the base plate before the PowerStone element 3 is
placed on top. Glue in place the transit element (5) for
the fresh air supply connection with the acrylic which
is included. If the fresh air supply is connected through
the bottom plate, the hole is sealed off with supplied
concrete lid (4).
If a fresh air supply set is not used, or if it is connected
at the rear, the concrete lid should be placed in the
recess in the bottom plate as shown in FIG 7. Whether
the fresh air supply is connected from below or rear it is
important that the connection between the flue and the
concrete is properly sealed off with the acrylic that is
included. This is to prevent leakage of cold air into the
home.
FIG 8-11
Assemble the inner core and the surround. The inner
core elements are equipped with gaskets on the contact
surface that is to face upwards. There is therefore no
need for further adhesives or sealing between each
element. Ensure that the surfaces are clean and even,
and that there are no pieces of concrete and similar that
may compromise the density between the elements.
The contact surfaces between the surround elements
are to be glued with the acrylic that is included. If acrylic
seeps out between the joints on the outside, remove it
before it dries with a wet sponge / finger.
Attention! Ensure that the inner core is mounted in
vertical, and that components are not displaced in
relation to each other. There should be a 6-10 mm air
gap between the inner core and the surround.
All manuals and user guides at all-guides.com
FIG 12
The 10 mm gasket that is to seal off the door frame
from the inner core is glued into the slot in the inner
core with the acrylic that is included.
If the gasket between the core and the door is not
sealing sufficiently above the door, use the enclosed
20x10 mm gasket for sealing
FIG 13
To ensure that the glass in the door is not damaged
during installation, remove the transportation lock
and lift the door up and out of the lower edge.
FIG14
Install the air ducts (a-b) on the doorframe. Unfasten
the air-diffuser (c). Install the upper and lower clamps
(d-e). Do not tighten the upper clamps, these should be
turned into place behind the next layer of PowerStone
and then tightened (FIG 16). When the door frame is
placed on the hearth, the air ducts will fit the gouge
as shown in FIG 14b. The gasket joint should overlap
the doorframe FIG 15. The doorframe must rest on the
gasket under door frame.
FIG 16-17
Mount the next PowerStone element. Now the door
frame can be attached with the fasteners as shown in
FIG 16. Do not use more force than that the door frame
is held loosely in place against the gasket, as excessive
force can displace the inner core. Light tensioning can
be done when the fireplace is fully assembled, the
weight of the elements will then prevent displacement.
Ensure that the door frame is mounted right at the
centre in relation to the lateral elements.
The distance between the surround and door frame
should be equal at both the top and the bottom. This
distance can be adjusted on the door frame system as
shown in FIG 27. The door must be removed in order
to do this, as shown in FIG 13. This can also be
fine-tuned after the entire fireplace has been mounted.
FIG 18-20
If the fireplace is supplied with additional top extension,
this assembly is described in FIG 18-20. If this
extension is not included, you can ignore these steps.
The Thermotte® plates, as shown in FIG 22 and
48, must be exchanged for longer versions when
assembling Salzburg M – High.
FIG 21-24
Assemble the reminder of the inner core and surround
elements.
FIG 25-26
You can now choose whether to place the bypass
damper arm on the right or the left side. The drilling in
the inner core and the surround element, as well as
the adjustment of the length of the arm must then be
GB
21