Monacor International PA-803DMP Mode D'emploi page 11

4.2 Music module
Button on the
remote control 
Button on the
module 
PWR × to switch the module on / off
to select the signal source:
FM = radio
MODE × ×
bt = Bluetooth receiver
USB = USB flash drive
SD = memory card
/ × to adjust the volume (U 00 ... U 32)
 
VOL– / VOL+ × Keep the button pressed on the
module to adjust the volume.
MUTE × to mute / unmute the sound
Radio
to automatically scan for stations
II ×
× and to save them to
SCAN
storage locations
0, 1... 9 × to select the storage location
I   /  I ×
previous / next storage location
PREV / NEXT ×
Audio player
Connect a USB flash drive to the jack USB and / or
insert a memory card (contacts facing upwards) into
the slot SD / MMC.
× × to pause / to continue the replay
II
0, 1... 9 × to select the title number
I   /  I ×
previous / next title
PREV / NEXT ×
repeat mode
ALL = repeat of all titles
×
ONE = repeat of a single title
to select sound presets
EQ ×
nor = normal, no modification
STOP × to stop the replay
Bluetooth receiver
The Bluetooth receiver can be used as an alternative to
the radio mode or the audio player mode. It is used
for wireless connection to a Bluetooth audio source
(e. g. smartphone or tablet computer).
1. Press the button MODE to select bt.
2. Activate the Bluetooth function at the Bluetooth
source. On the list of available devices, the amplifier
will appear as "UP-312B".
3. Pair the Bluetooth source with "UP-312B" (see the
manual of the Bluetooth source, if required). The
devices will be paired automatically.
To control the replay via Bluetooth, use the Bluetooth
source or the buttons on the module or the remote
control.
Subject to technical modification .
All manuals and user guides at all-guides.com
Function
5 Specifications
Amplifier
Power rating: � � � � � � � � � � � � � � � 30 W – PA-803DMP
THD: � � � � � � � � � � � � � � � � � � � � � < 0�5 %
Frequency range: � � � � � � � � � � � � 60 Hz – 15 kHz
Inputs
Sensitivity / impedance; connection
MIC 1: � � � � � � � � � � � � � � � � � � � � 4�5 mV/ 600 Ω; XLR bal�
MIC 2, MIC 3: � � � � � � � � � � � � � � 4�5 mV/ 600 Ω;
LINE 1, LINE 2: � � � � � � � � � � � � � � 140 mV/10 kΩ;
LINE 3, LINE 4: � � � � � � � � � � � � � 130 mV/ 10 kΩ;
TEL INPUT: � � � � � � � � � � � � � � � � 80 mV/600 Ω;
S / N ratio
Microphone inputs: � � � � � � � � 72 dB
Line inputs: � � � � � � � � � � � � � � 85 dB
Phantom power supply
for MIC 1: � � � � � � � � � � � � � � � � � ⎓ 48 V, switchable
Outputs
Speakers: � � � � � � � � � � � � � � � � � 4 / 8 /16 Ω, 70 / 100 V;
RCA jacks OUTPUT: � � � � � � � � � � mixed signal
MOH OUTPUT: � � � � � � � � � � � � � mixed signal without
General
Power supply
Mains: � � � � � � � � � � � � � � � � � 230 V/ 50 Hz
Power consumption: � � � � � � 100 VA – PA-803DMP
DC voltage: � � � � � � � � � � � � � � 24 V
Current consumption: � � � � � 2�5 A – PA-803DMP
Ambient temperature: � � � � � � � � 0 – 40 °C
Dimensions (W × H × D): � � � � � 320 × 95 × 245 mm
Weight: � � � � � � � � � � � � � � � � � � � 3�0 kg – PA-803DMP
All rights reserved by MONACOR
& Co. KG. No part of this instruction manual may be
reproduced in any form or by any means for any com­
mercial use.
60 W – PA-806DMP
120 W – PA-812DMP
6�3 mm jack, unbalanced
6�3 mm jack, unbalanced
RCA (L / R), unbalanced
screw terminals, unbal�
screw terminals
with line level
MIC 1 signal,
e� g� for music on hold;
screw terminals
160 VA – PA-806DMP
250 VA – PA-812DMP
4�2 A – PA-806DMP
8�4 A – PA-812DMP
6�7 kg – PA-806DMP
7�8 kg – PA-812DMP
® INTERNATIONAL GmbH
11