Maytag MVWB850YG0 Mode D'emploi page 2

FOR SERVICE TECHNICIAN ONLY – DO NOT REMOVE OR DESTROY
something is faulty with the button, and it is not
possible to enter the diagnostic mode.
If no indicators come on after pressing POWER/
CANCEL, press any other key, move the cycle
knob, or open the lid and repeat step 1.
If no indicators come on after that, go to TEST #1,
page 4.
Indication 2: Fault code flashes from the
display.
Action:
Review the Display Fault/Error Codes table,
page 3, for the recommended procedure.
DIAGNOSTIC: Saved Fault Codes
The washer will save up to 4 of the most recent
fault codes. Errors are not displayed or saved in
chronological order of appearance. If there are saved
fault codes (as indicated in step 3 of Activation of
Automatic Diagnostic Test Mode, page 1), the fault code
saved in the first memory location will be displayed and
show "F" and "XX" where XX is the fault code.
Press and release
the same button
Second memory location saved
used to activate fault code is displayed.
Diagnostics
Third memory location saved
Repeat
fault code is displayed.
Fourth memory location saved
Repeat
fault code is displayed.
All indicators momentarily turn
Repeat off, then stay on. After 5 seconds,
Automatic test cycle begins.
NOTE: Fault codes are retained, after displaying them
and/or interrupting power.
ACTIVATION OF MANUAL DIAGNOSTIC
TEST MODE
1. Read and perform steps 1 and 2 under
Activation of Automatic Diagnostic Test Mode,
page 1, and press the same button once during
the first 5 seconds of display of the
NOTE: If the button is not pressed within 5 seconds,
the Automatic test will start (after saved fault codes).
2. If done successfully, a single beep occurs and the
three-digit display shows the User Interface ID# (
H 81
, etc.) for 3 seconds, then displays
Add A Garment indicator LED flashes. See Diagnostic:
Manual, below.
DIAGNOSTIC: Manual
Enter Manual Diagnostic test mode, above. Three-digit display
000
shows , and Add A Garment indicator LED is flashing.
NOTE: If there is no activity (button press, cycle select)
within 5 minutes, the control automatically exits
Diagnostic mode and enters standby mode.
Manual: Water Valves
(See Manual Activation, above)
To check FRESH valve
select and press the following:
WHITES START/PAUSE (turns on Fresh valve,
cycle indicator flashes) WASH TEMP (selecting
hot = hot valve; warm = hot & cold valves; cold =
cold valve) START/PAUSE (turns off Fresh valve,
cycle indicator is steady on).
To check DETERGENT valve
select or press the following:
SUPER WASH or HEAVY DUTY START/PAUSE
(turns on Detergent valve, cycle indicator flashes)
WASH TEMP (selecting hot = hot valve; warm =
hot & cold valves; cold = cold valve) START/
PAUSE (turns off Detergent valve, cycle indicator
is steady on).
P A R T N O . W10403990A
To check FABRIC SOFTENER valve
the following:
NORMAL START/PAUSE (turns on Fabric Softener
valve, cycle indicator flashes) WASH TEMP
(selecting hot = hot valve; warm = hot & cold valves;
cold = cold valve) START/PAUSE (turns off
Fabric Softener valve, cycle indicator is steady on).
To check BLEACH valve
DELICATE/HANDWASH START/PAUSE (turns
on Bleach valve, cycle indicator flashes) WASH
TEMP (selecting hot = hot valve; warm = hot &
cold valves; cold = cold valve) START/PAUSE
(turns off Bleach valve, cycle indicator is steady on).
If any valve fails to turn on, go to TEST #2, page 4.
Manual: Pumps
Select CLEAN WASHER cycle.
Press and release:
START/PAUSE
Repeat
Repeat
Repeat
If pumps fail to turn on, go to TEST #7, page 6.
Manual: Lid Lock
NOTE: Lid must be closed. If lid is not closed, an invalid
button press beep will occur when performing next step.
Press and release:
WATER SAVE
SPRAY RINSE or
REMINDER RESET
Repeat
If lid does not lock or unlock, go to TEST #8, page 6.
Manual: Motor
8:88
.
Rotor Position Sensor (RPS):
and Spin indicators (if available) to detect the three
hall sensors. Console may have up to two of these
indicators on at one time when the basket is not moving.
H 80, Open lid and rotate basket by hand. The Wash, Rinse,
and Spin status indicators should toggle on and off
000
and the
according to direction the basket is being turned.
If none of these indicators are on, go to TEST #3,
page 4.
Spin:
To activate Spin, lid must be closed with lid lock
enabled. See Manual: Lid Lock test, at left.
NOTE: If lid is not closed, an invalid button press
beep will occur when performing next step.
Press and
release:
SPIN SPEED Motor/basket spins at 23 rpm.
Repeat
Repeat
Repeat
NOTE: Indicators to left of button scroll from right to left.
If motor fails to spin, go to TEST #3, page 4.
POUR LE TECHNICIEN SEULEMENT – NE PAS ENLEVER NI DÉTRUIRE
select or press
select or press the following:
(See Manual Activation, at left)
Turns on recirculation pump,
cycle indicator is steady on.
Turns off recirculation pump,
cycle indicator is steady on.
Turns on drain pump, cycle
indicator flashes.
Turns off drain pump, cycle
indicator is steady on.
(See Manual Activation, at left)
Lid locks, Lid Lock indicator
turns on.
Lid unlocks, Lid Lock
indicator turns off.
(See Manual Activation, at left)
Uses Wash, Rinse,
Motor/basket spins at 530 rpm.
Motor/basket spins at 1000 rpm.
Motor turns off.
P A G E 2
Agitate:
Water must cover the wash plate to
ensure the basket is floating prior to agitation.
Enabling agitation without enough water may cause
a fault condition to occur. See Manual: Water Valves
test, at left.
Press and release:
Gentle wash action.
SOIL LEVEL
Repeat Normal wash action.
Repeat Heavy wash action.
Repeat Motor turns off.
NOTE: Indicators to left of button scroll from right to left.
If motor fails to agitate, go to TEST #3, page 4.
Manual: Heater
(If supplied) (See Manual
Activation, at left)
Water must cover the wash plate to ensure the heater
is completely submerged. Heater will not be enabled if
there is less than 3" (75 mm) of water in the washer tub,
and the Cold valve needs to be active:
To turn on the Cold Valve:
Press WASH TEMP until selecting warm.
To turn on the Heater:
Select RINSE/DRAIN & SPIN cycle.
Press START/PAUSE.
ACTIVATION OF CONSOLE AND
INDICATORS DIAGNOSTIC TEST MODE
This test checks the cycle selector knob, indicators,
buttons, three-digit display, and beeper.
1. Plug in washer or reconnect power.
2. From Standby Mode (plugged in with all indicators
off) or Setting Mode (plugged in and power up just
before running a cycle), press and release (key-dance)
the following buttons within 4 seconds:
SOIL SOIL
WASH TEMP
LEVEL LEVEL
If successful, three digits will display "dt" and you will
have 5 seconds to complete next step.
3. Within 5 seconds of showing "dt" in display, press
START/PAUSE (all indicators in display are illuminated
8:88
and is displayed).
Press START/PAUSE a second time. This turns
off the three-digit display and all status indicators
except for the delay indicator (if present). All other
indicators remain illuminated.
P ress START/PAUSE a third time. This turns on
status indicators and three-digit display (all indicators
are illuminated).
Press DELAY START [+] or [–]. This turns off the
delay indicator (if available).
Press DELAY START [+] or [–]. This turns on the
delay indicator (if available).
Press REMINDER RESET. This turns on the CLEAN
WASHER REMINDER indicator.
4. Rotate WASH CYCLE selector back and forth.
Indicators will toggle on (or off).
5. Press buttons to verify function. Indicators will toggle
on (or off) and a beep tone will sound when buttons
are pressed. To indicate that all of the buttons were
pressed, the 7 segment display will show "P" at
the end of the test.
P È I C E N
WASH TEMP
o
W10403990A