Bosch Professional GWS 6-100 Instructions D'emploi page 8

2 609 140 063 - Buch Seite 4 Mittwoch, 11. Februar 2004 10:03 10
Mounting the Grinding Tools
Before any work on the machine itself, pull
the power plug.
Use only grinding tools whose allow-
able speed is at least as high as the
idling speed of the machine.
Grinding and cutting discs become very
hot during use; do not touch them until
they have cooled down.
Clean the grinder spindle and all parts to be
mounted. For clamping and loosening the
grinding tools, lock the grinder spindle 5 with
the spindle locking button 4.
Activate the spindle locking button 4 only
when the grinder spindle is at a standstill!
Grinding-/Cutting Disc
Observe the dimensions of the grinding discs.
The diameter of the hole must fit retainer
mounting flange 8 (M 14), 17 (M 10). Do not
use any reducers or adapters.
For mounting, see the illustration page.
Screw on the clamping nut 10 and tighten with
the two-hole spanner (see Section "Quick Clamp-
ing Nut").
8
If the O-ring is missing or damaged, it will have
to be replaced (Stock No. 1 600 210 039) before
the retainer mounting flange 8 is mounted.
17
After mounting the grinding tool but be-
fore switching it on, check that the
grinding tool is correctly mounted and
that it can turn freely.
9 • 2 609 140 063 • TMS • 04.02.04
All manuals and user guides at all-guides.com
Flap disc
(for M 14 grinder spindle)
Depending on the application and if necessary,
remove the protective hood 6 and mount the
hand protector 12. Place the special retainer
mounting
2 605 703 028) and the flap disc on the grinder
spindle 5. Screw on the clamping nut 10 and
tighten with the two-pin spanner.
Rubber Sanding Plate 13
Depending on the application and if necessary,
remove the protective hood 6 and mount the
hand protector 12.
For mounting, see the illustration page.
Screw on the round nut 15 and tighten with the
two-pin spanner.
Cup Brush 16/Disc brush
(for M 14 grinder spindle)
Depending on the application and if necessary,
remove the protective hood 6 and mount the
hand protector 12.
The grinding tool must be screwed onto the
grinder spindle 5 until it rests firmly against the
grinder spindle flange at the end of the grinder
spindle threads. Tighten with an open-ended
spanner.
Retainer mounting
flange for grinding
Quick Clamping Nut
spindle M 14
An O-ring (plastic
(for M 14 grinder spindle)
part) is inserted in
The quick clamping nut 11 (accessory) can be
the retainer mount-
used instead of the clamping nut 10. Grinding
ing flange 8 around
tools can be mounted without using tools.
the spigot.
The quick-clamping nut 11 may be used only
for grinding and cutting discs.
Use only a flawless, undamaged quick clamp-
ing nut 11.
Retainer mounting
When screwing on, take care that the printed
flange for grinding
side does not point to the grinding disc. The
spindle M 10
arrow must point to the index mark 18.
The mounting
flange 17 can be
used on both sides.
Do not use reducer
pieces or adapters.
English - 4
flange 8 (accessory,
Lock
spindle with the spin-
18
dle locking button 4.
Tighten
clamping
forcefully turning the
grinding disc clock-
11
wise.44
4
Stock No.
the grinder
the quick
nut by