RAUMER Ancrage Antrax Notice Technique page 3

ENGLISH
General informa on about RAUMER products comply with
Direc ve 89/686/CEE
This general informa on explains how to use correctly the anchors.
The general informa on must be associated to the technical data sheet and the inspec on sheet. Read
both documents to have a complete informa on and ascertain to understand well all the informa ons,
before to use the product. Only the techniques shown without symbol of death are authorized. Take
Vision of the updates and of all the addic onal informa ons on the site www.raumerclimbing.com
In case of doubt or difficulty to understand the informa ons, don't risk, but contact Raumer Srl – Via
Lago di Lesina 15B – 36015 Schio (VI).
Anchor Antrax – Art. 298
Anchor Superstar – Art. 160 and variants: Art. 119 – Art. 518
Anchor Masterfix – Art. 151 and variants: Art. 125 – Art. 525
Anchor Radius – Art. 519 and variants: Art. 520 – Art. 521
Reference Standards:
Rock anchor - EN 959: 2007
Anchor device intended for
permanent installa on – UNI 11578 po A
UIAA 123-2
Material: Stainless Steel AISI 316 L
USE AND APPLICATION
The anchors Antrax Art. 298, Superstar Art. 160 – 119 – 518, Masterfix Art. 151 – 125 – 525,
Radius Art. 519 – 520 – 521, are type A anchors, tested according to UNI 11578:2015, including
fixed anchors points, intended for permanent installa on, above or in the structure, designed to
accomodate a connected user and an an fall system according to UNI EN 363.
They're anchors for the protec on against fall from a height, designed for use in climbing, caving,
canyoning and mountaineering.
They're also tested according to EN 959:2007 designed for use as rock anchors; rock anchors are
defined as anchor devices insert in a rock hole, held in place by resin (or expansion forces) and
with an a achment point for a connector.
The anchor device is tested according to UIAA 123-2 - rock anchors.
When the anchor device is used as part of a fall arrest system, the user must be equipped with
the necessary means to limit the maximum dynamic forces exerted on them during the arrest of
a fall with a maximum of 6 kN.
Warning: this anchor device must be used exclusively for protec on against falls from a height
and not for li\ing equipment. This anchoring device is also designed for use in reten on.
Don't stress the product beyond its limits or in other different situa ons than that for which it is
intended. Check that the product is compa ble with the other materials you want to use: contact
Raumer if you are not sure of compa bility.
A7en on: ac vi es involving the use of this device are all dangerous and high-risk and may
also involve in fatal injuries. Make sure you fully understand the use of this product and work
out in how to use it, to familiarize yourself with it and learn to know its performances and
limits.
Art. 160 – 119 – 518 – 151 – 125 – 525 – 519 – 520 - 521
NOMENCLATURE
DYNAMIC STRENGHT TESTS
1) Direc on parallel to logitudinal axis of the device
2) Direc on perpendicular to logitudinal axis of the device
Peak of force: 9 kN
Maximum deflec on of anchor device: 5 mm
Maximum displacement of anchor point:5 mm
The material is suitable to dynamic strength tests and integrity tests.
MARKING
Producer: Raumer Srl – iden fied with logo "Raumer"
Iden fica on of the model – Art. n. (es. 298)
Pictogram indica ng the need to
read the instruc ons before use:
Lot number: (es. 001)
Month and year of manufacture: (es. 0515 = may 2015)
Reference Standards: UNI 11578:2015
EN 959:2007
Radius: Axial Load bearing capacity: 30 KN Radial load bearing capacity: 30 KN
Masterfix: Axial Load bearing capacity: 35 KN Radial load bearing capacity: 35 KN
Superstar: Axial Load bearing capacity: 30 KN Radial load bearing capacity: 30 KN
Antrax: Axial Load bearing capacity: 27 KN Radial load bearing capacity: 26 KN
See the table on the a ached data sheet, with the effec ve resistance.
Material: Stainless Steel INOX AISI 316 L
Device usable by only a single connected user: 1P
Markings should always be read for all the life me of the product and must not be removed.
It's recommended that the anchor device is marked with the date of the next or last inspec on.
If the marking of the connector is no longer accessible a\er installa on, it must be provided
some addi onal markings near the device.
Risks of use and responsibility
This product should only be used by competent persons and who have received adequate
training, having been subjected to visual inspec on by a trained and competent person.
It's yours responsibility to know this product, learn to use it, learn the proper tecniques and the
safety measures.
You alone are solely fully all risks and responsibili es for any damage, injury or death which may
derivar to yourself or others persons, following incorrect use of each kind of product of the
company RAUMER Srl. Keep these instruc ons that describe the range of use and the methods of
applica on of the product.
You are responsible to consider all the no ces and updates regarding these products.
No liability will be recognized by the company Raumer Srl for damages, injuries or death caused
by: improper use (also due to support or unsuitable environment), stresses the product beyond
its limits, modifica on of the product, repairs made by unauthorized persons.
If you are not able to undertake this responsibility and take these risks, do not use these
products. Your life depends on the con nual efficiency of your equipment (we strongly
recommend that the equipment is for personal use) and its history (use, storage, controls, etc.)
If the product is not for personal use (for exemple is of associa ons), we strongly recommend
that the pre and post- use controls carried out by a competent person.
Check and make sure that all the anchors do not show signs of cracks or wear.
Before using the equipment consider as a possible rescue, in case of emergency, it can be
performed safely and efficiently.
stem A en on! Do not use the product if the user's physical condi ons are not appropriate for work
prescribed. Do not use this product if you suffer from medical condi ons such as ver go,
labyrinthi s or other condi ons which may compromise the safety of the equipment in normal
eyelet use or emergency.
CHECKS AND INSPECTIONS
Before each use
Before each use, make sure that the product is:
– in very good condi on and working properly;
– suitable for the use you intend to do: they are authorized only the techniques not
crossed out; any other use is forbidden: beware of death! The examples shown in
the a ached form are just some of the wrong applica ons: there are many other
more that is impossible to list;
– free of cracks, deforma ons and corrosions ;
Carefully check the state and the type of support in that you want to fix the product; if the rock is
cracked, etc. ... avoid it. If you have the minimum doubt about the safety and the effec veness of
the product, replace it immediately.
During each use
Regularly check the state of the product and make sure you have correctly connected all devices
among themselves . Check visually the goodness of the anchor.
The resistance of natural/not natural anchors, in the rock, can't be guaranteed in advance, so It's
necessary a cri cal judgment by the user, to guarantee an appropriate protec on.
Periodical inspec ons
It's not enough to check the material before and during each use, but periodical checks must be
done by a technician authorized by the manufacturer at least every 2 years for controls rela ng
to the anchoring system and 4 years for the controls rela ve to the support structure and the
anchors. All the checks pre and post use must be done by a competent person (the frequency
depends from the intensity and type of use).
When carrying out the checks is necessary to report the results of an inspec on sheet; this
should allow you to record a lot of data; The inspec on sheet should always be a ached to the
general informa on of the
www.raumerclimbing.com.
Cau on: You must make regular periodic inspec ons! The safety of users depends on the
con nued efficiency and durability of the equipment.
We recommend to hold and fill the inspec on sheet for each component, system and sub-
system. You can also download it from the site www.raumerclimbing.com
COMPATIBILITY
This product can be used in conjunc on with personal protec ve equipment, in compliance with
Direc ve 89/686 / EEC and in accordance with the instruc ons of use (if devices are compa ble
there is a good func onal interac on). An anchor must be compa ble to the device to which it is
connected; if the connec on is inconsistent, you can compromise the security features of the
system (release or break ...). Compa ble devices are, for example, manufactured and cer fied
harnesses according to EN 12277, dynamic ropes cer fied according to EN 892, connectors in
accordance with EN 362 or 12275, etc ...
Warning: Please avoid the use of these anchors with others made of different materials. For
example, do not use plates made of stainless steel and galvanized steel anchors, because also in
a modest hos le environment there will be obtained effects of galvanic corrosion.
Contact Raumer if you are not sure of the compa bility of your device.
OPERATING MODE
Placing anchors using a resin glue is a simple but delicate process.
If not executed correctly, resistance to tensile and shear force can be seriously compromised.
There are two recommended types of resin glue:
A) BICOMPONENT EPOXY RESIN PACKAGED IN CARTRIDGES.
B) SYNTHETIC ACYRLATE RESIN PREDOSED IN GLASS PHIALS.
Instruc ons for each system are as follows:
Method "A"
product and is also downloadable from the
05 - 2015
site