Maintenance And Storage - Alpina AS 45 E Mode D'emploi

EN
A. Stop the motor.
B. Leave the site in the opposite direction from the
damaged point on the cable.
C. Disconnect the cable from the power socket.
• Stop the motor and disconnect the power supply:
A. If the driver leaves the machine.
B. If the auger housing or discharge chute is blocked and
must be cleaned.
C. Before beginning repairs or adjustments.
• Always make sure the rotating parts have stopped and all
the controls are disengaged before cleaning, repairing or
inspection.
• Never drive across a slope. Move from the top down, and
from the bottom to the top. Be careful when changing
direction on a slope. Avoid steep slopes.
• Never operate the machine with insufficient protection or
without the safety devices in place.
• Existing safety devices must not be disconnected or
disengaged.
• Never use the snow thrower near enclosures, cars,
windowpanes, slopes etc. without properly setting the
discharge chute deflector.
• Always keep children away from areas to be cleared. Get
another adult to keep the children under supervision.
• Do not overload the machine by driving it too fast.
• Take care when reversing. Look behind you before and
during reversing to check for any obstacles.
• Never point the discharge chute towards bystanders. Do
not allow anyone to stand in front of the machine.
• Disengage the auger when the snow thrower is to be
transported or is not in use Do not drive too fast on
slippery surfaces when transporting.
• Only use accessories that are approved by the machine's
manufacturer.
• Never drive the snow thrower in bad visibility or without
satisfactory lighting.
• Always ensure you have a good balance and a tight grip
on the handle.
2.4

MAINTENANCE AND STORAGE

• Tighten all nuts and screws so that the machine is in safe
working condition.
• Never flush the machine with water. It will make damage
to the electrical equipment and risk of electrical shocks.
• Check all electrical equipment before use. The snow
thrower must never be used if its insulatings, fittings or
other electrical equipment is damaged.
• Always use genuine spare parts. Non-genuine spare parts
can entail a risk of injury, even if they fit the machine.
• Before a long storage, check the instructions for
recommendations.
• Replace damaged warning and instruction stickers.
• Let the engine run a couple of minutes with the auger
connected after use. This prevents the auger from
freezing solid.
24
All manuals and user guides at all-guides.com
ENGLISH
3.1
1. Open the box carefully.
2. Take care of any documentation in the box, for example
3. Lift the snow thrower from the box.
4. Cut the tie straps holding the chute control shaft to the
5. Dispose of the box and packaging according to local
3.2
1. Unfold the handle.
2. Tighten the four knobs (1:D).
3. Secure the cable to the handle with two clamps (1:C).
3.3
1. Place the shaft through the loop on the handle (2:L).
2. Insert the shaft in the joint (2:M). Make sure the holes in
3. Lock the shaft by tightening the screw (3:N) all the way
4. Check the discharge chute by turning it fully in both
The snow thrower is fitted with the following controls and
devices.
Starting handle (1:A) – Starts and stops the electric motor.
Ignition lock (1:K) – Facilitates activation of the starting
handle.
Connector (1:J) – For electrical connection.
Cable support (1:B) – For supporting the connection cable.
Deflector lock (1:E) – Locks the deflector in position.
Chute control lever (1:F)– Changes the direction of the
discharge chute.
Discharge chute (1:H) – Ejects the snow.
Deflector (1:I) – Determines the distance the snow is
thrown.
3 ASSEMBLY
UNPACKING
these instructions.
side of the handle.
regulations.
HANDLE
CHUTE CONTROL
the shaft and the joint are aligned.
through the shaft and joint.
directions. The chute should rotate freely.
4 CONTROLS