Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
INDEX
1. Prior to assembling the insert
EC CONFORMITY DECLARATION
Date of issue: 10.09.2008
Conformity declaration issued by:
Company name:
Address:
Postal:
Country:
Phone:
Fax:
Web:
E-mail:
Identification:
Product type:
Insert type:
Fuel type:
Flue gas temperature:
CO content at 13 % O
:
2
Thermal output, nominal value:
Energy efficiency:
Safety measurements:
Minimum distance to adjacent
combustible materials:
Country
Classifications
EUR
Intermittel
General manager, Nordpeis AS
Rapport Nr. RRF - 29 09 1914
Inspection code: 1625
Rhein-Ruhr Feuerstättenprüfstelle GmbH
Am Technologiepark 1, D-45307 Essen
10
10
All manuals and user guides at all-guides.com
Nordpeis AS
Gjellebekkstubben 9/11
N-3420 Lierskogen
Norway
(+47) 32 24 47 00
(+47) 32 24 47 11
www.nordpeis.no
post@nordpeis.no
Nordpeis N-21
Fireplace insert
Steel fireplace insert burning solid fuel
firewood only - see manual
297 ºC
0,09 %
6,0 kW
79,2 %
Only to be used in non-combustible surrounds.
Must be used in accordance with user manual.
Must be placed in accordance with user manual.
Test standard
Approved by
EN 13229
RRF
Stian Varre
1. Prior to assembling the insert
Our surrounds are all made of non-combustible
10
materials. All our inserts/stoves are tested according
10
to the latest European requirements and also to the
10
Norwegian SINTEF standard, which includes particle
11
tests. Several European countries however have
11
individual rules for installation of inserts, stoves and
fi replaces.
11
The client is entirely responsible for the fulfi lling of
11
these local rules concerning the installation in his
12
region/country. Nordpeis (Northstar) is not responsible
12
regarding correct installation. You should check local
12
regulations concerning: distance from fi rebox to
12
combustible/fl ammable materials, insulation materials/
requirements between fi replace surround and back
12
wall, size of fl oor plates in front of fi replace/stove if
12
required, fl uepipe connection between fi rebox and
13
chimney and insulation requirements if fl uepipe goes
13
through infl ammable wall such as a wooden wall.
13
13
For your own safety, comply with the user
manual. All safety distances are minimum
14
distances. Installation of the insert must
comply with the rules and regulations of the
country where installed. Nordpeis AS is not
15
responsible for wrongly assembled inserts.
Chimney Draught
Compared with older models, the clean burning
inserts of today put signifi cantly higher demands
on the chimney. Even the best insert will not work
properly if the chimney does not have the right
dimensions or is not in good working order. The
draught is mainly controlled by gas temperature,
outside temperature, air supply as well as the height
and inner diameter of the chimney. The diameter of
the chimney should never be less than that of the fl ue/
chimney collar. At nominal effect there should be a
negative pressure of 14 to 25 Pascal.
The draught increases when:
•
The chimney becomes warmer than the outside air
•
The active length of the chimney is increased (over
the hearth)
•
Good air supply to the combustion
It can be diffi cult to obtain the right draught conditions
in case the chimney is too large in relationship to
the fi replace, as the chimney does not heat up well
enough. If possible, insert a smaller chimney pipe.
Draught that is too strong can also be controlled with
a damper.
Air Supply
A set for fresh air supply is available as an accessory,
and will ensure that ventilation systems, kitchen fans
and other factors that can create a downdraught in the
room of the fi replace affect less the air supply to the
insert. Insuffi cient air supply can cause downdraught
and thereby low combustion effi ciency and the
problems that this entails: soot stains on the glass,
ineffi cient use of the wood and a soot deposits in the
chimney.
GB
Publicité
Chapitres
Table des Matières
