X-lite X-1004 Sécurité Et Instructions D'utilisation page 12

Repeat the same operation on the right side of the helmet.
WARNING
- Make sure the VPS operates correctly by moving the left side slider towards the bottom (Fig.12A) and the top
side of the helmet (Fig.12B). If necessary, repeat the above-mentioned steps.
- If the VPS opening/closing mechanisms are not working properly or if such mechanisms get damaged,
please contact an X-Lite authorized dealer.
- Do not use the helmet if the VPS has not been assembled properly.
- Since the VPS does not assure you the same protection as the one provided by the visor, it has to be used
only when the helmet visor is lowered.
REMOVABLE INNER COMFORT PADDING
To remove the inner comfort padding, lift the VPS and the chin guard of the helmet (see instructions above).
9. Disassembly of the Roll Neck
9.1. Open the chin strap (see specific instructions) and remove the chin strap band from the elastic loops on the
strap and/or on the roll neck (Fig.14).
9.2. Pull the front of the left cheek pad towards the inside of the helmet to release the front button on its back
(Fig.15).
9.3. Release the roll neck eyelet fastener (Fig.16) and refasten the left cheek pad.
9.4. Follow the same steps on the other side of the helmet.
9.5. Open the zip and remove the roll neck (Fig.17).
10. Assembly of the Roll Neck
10.1. Unfasten the chin strap (see relevant instructions).
10.2. Insert the roll neck, fasten and then close the zip (Fig.17).
10.3. Pull the front of the left cheek pad towards the inside of the helmet to release the front button on its back
(Fig.15).
10.4. Fasten the roll neck eyelet fastener (Fig.16) and refasten the left cheek pad.
10.5. Follow the same steps on the other side of the helmet.
10.6. Insert the chin strap band into the elastic loops on the strap and/or on the roll neck (Fig.14).
Repeat the same operation on the right side of the helmet.
WARNING
- Make sure the VPS operates correctly by moving the left side slider towards the bottom (Fig.12A) and the top
side of the helmet (Fig.12B). If necessary, repeat the above-mentioned steps.
- If the VPS opening/closing mechanisms are not working properly or if such mechanisms get damaged,
please contact an X-Lite authorized dealer.
- Do not use the helmet if the VPS has not been assembled properly.
- Since the VPS does not assure you the same protection as the one provided by the visor, it has to be used
only when the helmet visor is lowered.
REMOVABLE INNER COMFORT PADDING
To remove the inner comfort padding, lift the VPS and the chin guard of the helmet (see instructions above).
9. Disassembly of the Roll Neck
9.1. Open the chin strap (see specific instructions) and remove the chin strap band from the elastic loops on the
strap and/or on the roll neck (Fig.14).
9.2. Pull the front of the left cheek pad towards the inside of the helmet to release the front button on its back
(Fig.15).
9.3. Release the roll neck eyelet fastener (Fig.16) and refasten the left cheek pad.
9.4. Follow the same steps on the other side of the helmet.
9.5. Open the zip and remove the roll neck (Fig.17).
10. Assembly of the Roll Neck
10.1. Unfasten the chin strap (see relevant instructions).
10.2. Insert the roll neck, fasten and then close the zip (Fig.17).
10.3. Pull the front of the left cheek pad towards the inside of the helmet to release the front button on its back
(Fig.15).
10.4. Fasten the roll neck eyelet fastener (Fig.16) and refasten the left cheek pad.
10.5. Follow the same steps on the other side of the helmet.
10.6. Insert the chin strap band into the elastic loops on the strap and/or on the roll neck (Fig.14).