Description Of The Device; Setting The Clock - camry Premium CR 1113 Mode D'emploi

16. If using the device in bathroom after use remove the power plug from the socket,
because water proximity presents risk, even if the device is turned off.
17. Do not allow the device or power adaptor to wet. If the device falls into water,
immediately remove the power plug or power adaptor from the socket. If the device is
powered, do not put hands in the water. Have the device checked by the qualified
electrician before using it again.
18. Do not touch the device or power adaptor with wet hands.
19. The device has to be turned off after every use.
20. In order to provide additional protection, it is recommended to install residue current
device (RCD) in the power circuit, with residual current rating not more than 30 mA.
Contact professional electrician in this matter.
21. If the device utilises a power adaptor, do not cover it, because this can cause a
dangerous temperature rise and can damage the device. Always connect the power
adaptor cable to the device, and then connect the power adaptor to the power socket.
22. To save energy, if there is no audio signal from Turntable /AUX IN for a period of over 5
minutes, then the unit will automatically switch to Standby Mode.

DESCRIPTION OF THE DEVICE

1. Turntable cover
2. LCD display
3. Power diode
4. In-built speaker
5. FUNCTION button
6. SLEEP/TIMER button
7. Headphone port
8. SNOOZE button
9. MODE/CLOCK button
10. TUNER SCAN button
11. BAND button
12. TUNING DOWN button
13. TUNING UP button
14. AUX port

SETTING THE CLOCK

Before first use, unpack everything and remove all protective materials. Unwind the FM antenna cable and power cable. Do not cover
the ventilation holes, make sure that there is a gap of a few centimeters around the radio, which is required for proper ventilation.
1. In standby mode, press and hold the MODE/CLOCK button (9) to set the 12H or 24H clock mode. '12H/24H' will start flashing on the
display (2). Using the TUNING DOWN button (12) or TUNING UP button (13) select either the 12-hour or 24-hour mode and confirm
by pressing the MODE/CLOCK button again (9). The device will enter the hour editing mode.
2. Using the TUNING DOWN button (12) or TUNING UP button (13) set the current hour and confirm by pressing the MODE/CLOCK
button again (9). The device will enter the minute editing/ mode.
3. Using the TUNING DOWN button (12) or TUNING UP button (13) set the current minute and confirm by pressing the MODE/CLOCK
button again (9).
SETTING THE ALARM (RADIO ALARM FUNCTION)
1. In standby mode, press and hold the SLEEP/TIMER button (6). The display will show a clock icon and '0:00' will be flashing.
2. Using the TUNING DOWN button (12) or TUNING UP button (13) set the desired alarm hour and confirm by pressing the
SLEEP/TIMER button (6).
3. Using the TUNING DOWN button (12) or TUNING UP button (13) set the desired alarm minute and confirm by pressing the
SLEEP/TIMER button (6). The alarm time will be set.
4. The clock icon informs that the alarm is set. To turn the alarm off press the SLEEP/TIMER button (6) when the device is in standby
mode. The clock icon will disappear.
5. When the alarm is activated, the device can be put into 'snooze' mode by pressing the 'SNOOZE' button (8). The device will then
15. PRESET DOWN button
16. PRESET UP button
17. ON/OFF switch/volume control
18. 45RPM disc adaptor
19. Turntable lever
20. Turntable arm lock
21. Plate spin speed adjustment
22. Turntable arm
23. Turntable needle guard
24. LINE OUT jack
25. FM antenna cable
26. Power cord
27. AUTO-STOP switch
4