Dremel 4000 Traduction De La Notice D'origine page 21

sory
SAFETY WARNINGS SPECIFIC TO
GRINDING AND ABRASIVE CUTTING-OFF
er
your a. Use only wheel types that are recommended for
ory your power tool and the specific guard designed
o for the selected wheel. Wheels for which the power
tool was not designed cannot be adequately guarded
and are unsafe.
nd b. Wheels must be used only for recommended
applications. For example: do not grind with the
ause
side of cut-off wheel. Abrasive cut-off wheels are
intended for peripheral grinding, side forces applied to
these wheels may cause them to shatter.
c. Always use undamaged wheel flanges that are of
correct size and shape for your selected wheel.
y
Proper wheel flanges support the wheel thus reducing
the possibility of wheel breakage. Flanges for cut-off
s, wheels may be different from grinding wheel flanges.
d. Do not use worn-down wheels from larger power
tools. Wheel intended for larger power tool is not
a
g of suitable for the higher speed of a smaller tool and may
burst.
g
ADDITIONAL SAFETY WARNINGS
s.
SPECIFIC TO ABRASIVE CUTTING
le
a. Do not "jam" the cut-off wheel or apply excessive
pressure. Do not attempt to make an excessive
S
depth of cut. Overstressing the wheel increases the
d loading and susceptibility to twisting or binding of the
sory. wheel in the cut and the possibility of kickback or wheel
breakage.
ed b. Do not position your body in line with and behind
the rotating wheel. When the wheel, at the point of
operation, is moving away from your body, the possible
by kickback may propel the spinning wheel and the power
nto tool directly at you.
c. When wheel is binding or when interrupting a cut
may for any reason, switch off the power tool and hold
ng the power tool motionless until the wheel comes to
a complete stop. Never attempt to remove the cut-
e off wheel from the cut while the wheel is in motion
otherwise kickback may occur. Investigate and take
nd corrective action to eliminate the cause of wheel binding.
d. Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed and
carefully re-enter the cut. The wheel may bind, walk
sist up or kickback if the power tool is restarted in the
f workpiece.
or e. Support panels or any oversized workpiece to
n minimize the risk of wheel pinching and kickback.
r Large workpieces tend to sag under their own weight.
Supports must be placed under the workpiece near the
ory. line of cut and near the edge of the workpiece on both
sides of the wheel.
e f. Use extra caution when making a "pocket cut" into
existing walls or other blind areas. The protruding
ack
l's wheel may cut gas or water pipes, electrical wiring or
objects that can cause kickback.
SAFETY WARNINGS SPECIFIC TO
e a
loss
a. Be aware that wire bristles are thrown by the
brush even during ordinary operation. Do not
nt overstress the wires by applying excessive load to
the brush. The wire bristles can easily penetrate light
clothing and/or skin.
b. If the use of a guard is recommended for wire
brushing, do not allow any interference of the
All manuals and user guides at all-guides.com
OPERATIONS
OFFOPERATIONS
WIRE BRUSHING OPERATIONS
wire wheel or brush with the guard. Wire wheel or
brush may expand in diameter due to work load and
centrifugal forces.
c. Do not exceed 15,000 RPM when using wire
brushes.
ENVIRONMENT
DISPOSAL
The machine, accessories and packaging should be sorted
for environmental-friendly recycling.
ONLY FOR EC COUNTRIES
Do not dispose of power tools with household
waste!
According the European Guideline 2012/19/EC
for Waste Electrical and Electronic Equipment
and its implementation into national law, power tools that
are nolonger usable must be collected separately and
disposed of in an environmentally-correct manner.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Voltage Rating . . . . . . . . . 230-240 V, 50-60 Hz
Related Power . . . . . . . . . 175 W
Rated Speed (n( . . . . . . . 35,000 RPM
Collet Capacity . . . . . . . . 0.8 mm, 1.6 mm, 2.4 mm,
3.2 mm
Class II construction Double insulated construction
. .
tools
(PICTURE 5(
EXTENSION CORDS
Use completely unrolled and safe extension cords with a
capacity of 5 Amps.
ASSEMBLY
ALWAYS UNPLUG MULTITOOL BEFORE CHANGING
ACCESSORIES, CHANGING COLLETS, OR SERVICING
THE TOOL.
GENERAL
The Dremel multitool is a high quality precision tool that can
be used to perform detailed and intricate tasks. The wide
range of Dremel accessories and attachments allow you to
perform a large variety of tasks. These include tasks such as
sanding, carving, engraving, routing, cleaning and polishing.
PICTURE 6
A. Shaft lock button
B. On/Off switch
C Variable speed dial
D. Power cord
E. Hanger
F. Ventilation openings
G. Collet wrench
H. Shaft
I. Housing cap or EZ Twist™ integrated wrench/nose cap
J. Collet nut
21