DeWalt PATMI P1000 Manuel D'instructions page 6

Model P1000
10. do not fire tool within 3" (three inches) of the edge of a
concrete base material or within 1/2" (one-half inch) of
the edge of a steel base material.
11. do not attempt to install a fastener closer than 3" (three
inches) to another previously inserted fastener in concrete
or 1-1/2" (one and one-half inch) in steel.
12. do not fasten into a concrete base material less than 3
times as thick as the fastener penetration or into a steel
base material thinner than 1/8".
13. never attempt to install a fastener in a cracked or spalled
area in concrete. Place fastener at least 3" (three inches)
away from a spalled area to prevent the possibility of the
fastener bending and striking an operator or bystander.
14. do not attempt to install fasteners in areas that have
been welded or cut with a torch as these procedures
may have caused local hardening of the steel.
15. do not fasten through a predrilled hole unless proper
guidance is provided.
16. if you decide not to make a fastening after the tool has
been loaded, you must always remove the powder load
first followed by the fastener.
17. never attempt to override the safety features of this tool.
hanDling The Tool anD poWDeR loaDS
1. never leave a loaded tool unattended. once the tool
is loaded, make the fastening immediately or unload
the tool.
2. always unload the tool before work breaks, changing
parts, cleaning or servicing, and when storing.
3. to prevent accidental discharge of loads, never carry the
powder loads in the same container as the fasteners or
other hard objects.
4. always store the powder loads in the containers provided
or in an enclosure provided for them. never intermix the
various power levels. keep them segregated in clearly
identified containers.
5. Powder loads should never be used in firearms. they are
normally more powerful that the cartridges supplied with
the firearms.
6. Powder actuated tools and powder loads should always
be stored under lock and key. tools must be unloaded
when not in use.
Tool MalFuncTion
1. in the event that a load fails to discharge after the trigger is
pulled, the tool must be kept depressed against the work
surface for a minimum of 30 (thirty) seconds in case of a
delayed load discharge. then carefully remove the entire
load strip. and dispose of it in a can of water or other
nonflammable liquid. never attempt to force or pry a load
out of a tool chamber.
2. never discard unfired powder loads into a trash container.
3. do not attempt to unload or disassemble a jammed,
stuck or broken tool as improper handling may cause
it to discharge and strike operator and/or bystander. a
jammed tool must be pointed in a safe direction at all
times. tag the tool and lock it up. call your d
fasteners representative for proper assistance.
P1000
Fastener Selection Guide
300 heaD DiaMeTeR DRive pinS
CAT SHANK
NO. LENGTH
ddf3011000 1/2" k
ddf3011050 5/8" k
ddf3001100 3/4"
ddf3001150 1"
ddf3001200 1-1/8"
ddf3001250 1-1/4"
ddf3001300 1-1/2"
ddf3001350 1-3/4"
ddf3001400 2"
ddf3001450 2-1/4"
ddf3001500 2-3/8"
ddf3001550 2-1/2"
ddf3001600 2-3/4"
ddf3001650 3"
.300 heaD DiaMeTeR DRive pinS WiTh Top haT
CAT SHANK
NO. LENGTH
ddf3031000 1/2" k
ddf3031050 5/8" k
ddf3031100 3/4"
ddf3031150 1"
.300 heaD DiaMeTeR STep Shank pinS
CAT SHANK
NO. LENGTH
ddf3041000 3/4" step shank 100
ddf3041050 1" step shank
.300 heaD DiaMeTeR DRive pinS
WiTh 3/4" WaSheR
CAT SHANK
NO. LENGTH
ddf3051100 3/4"
ddf3051200 2-1/2"
.300 heaD DiaMeTeR DRive pinS
WiTh 7/8" WaSheR
CAT SHANK
NO. LENGTH
ddf3061150 1"
ddf3061250 1-1/4"
ddf3061300 1-1/2"
ddf3061400 2"
ddf3061550 2-1/2"
ddf3061650 3"
walt
e
.300 heaD DiaMeTeR DRive pinS WiTh 1" WaSheR
CAT SHANK
NO. LENGTH
ddf3071000 1-1/4"
ddf3071050 1-1/2"
ddf3071250 2"
ddf3071150 2-1/2"
ddf3071200 3"
6
Cat. No. ddF211000P
STD. STD. HEAD SHANK
BOX CTN DIA. DIA.
100 5000 .300 .143
100 5000 .300 .143
100 5000 .300 .143
100 5000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
STD. STD. HEAD SHANK
BOX CTN DIA. DIA.
100 5000 .300 .143
100 5000 .300 .143
100 5000 .300 .143
100 5000 .300 .143
STD. STD. HEAD SHANK
BOX CTN DIA. DIA.
1000 .300 .143/130 .5
100 1000 .300 .143/130 .6
STD. STD. HEAD SHANK
BOX CTN DIA. DIA.
100 1000 .300 .143
100 1000 .300 .143
STD. STD. HEAD SHANK
BOX CTN DIA. DIA.
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
STD. STD. HEAD SHANK
BOX CTN DIA. DIA.
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
100 1000 .300 .143
WT./
100
.5
.5
.5
.6
.7
.8
.9
1.1
1.2
1.2
1.3
1.4
1.6
1.9
WT./
100
.5
.5
.5
.6
WT./
100
WT./
100
1.6
2.5
WT./
100
1.9
2.0
2.1
2.4
2.7
3.0
WT./
100
2.2
2.3
2.6
2.9
3.2