EINHELL 36.533.00 Instructions De Montage page 3

Anleitung_Stegplatten_SPK7:_
page 10
15/c External view of the front wall
Profile view (h-profile / floor profiles)
Profile view (compensation profile / rain gutter)
Insert the web panels into the front wall. Position the two wider
panels directly next to the corner profiles and the narrower panels
directly next to the door cutout. Slide the bottom web panels to-
gether with the h-profiles into the notch in the floor profile.
Insert the web panels together with the compensation profile into
the notch in the rain guttering profile at the top.
page 11
15/d External view (detail of corner strut clip)
15/e Profile (single clip / door hinge)
15/f Profile (single clip / corner profile)
15/g Profile (single clip / corner strut)
Press the clips into the notches on the aluminium profiles provided
for this purpose.
Tip: Tap the clips gently with the supplied assembly tool and a rub-
ber mallet to secure them. A second person should press against
the aluminum profile from the inside during the assembly process.
page 12
16. Assembly of the plastic web panels on the
rear wall
Assemble the web panels at the rear wall as described in step 15.
To do so, perform assembly steps 15/a to 15/g again. In addition
two further web panels are fastened in the middle of the rear wall
between the floor and parapet profile. Follow the following assem-
bly steps.
page 13
16/a Bottom web panels
h-profiles are fastened to the bottom of the web panels. The longer
side of the h-profile points towards the inside. Tap the h-profile
gently with a rubber mallet so that engages correctly on the web
panel.
16/b External view of the rear wall
page 14
16/c Profile views of the parapet profiles
Slacken the parapet profiles slightly so that you can slide the web
panels completely under the parapet profiles.
16/d Detail view of the profiled strip
Working from the side, slide the web panels at the door hinges into
the profiled strips. Use no clips.
page 15
16/e External view (detail of middle corner strut clip)
16/f Profile (single clip / middle corner profile)
Tip: Tap the clips gently with the supplied assembly tool and a rub-
ber mallet to secure them. A second person should press against
the aluminum profile from the inside during the assembly process.
17.02.2009 16:39 Uhr Seite 3
Seite 16
17. Assembly of the plastic web panels on the
sides
page 17
17/a Bottom web panels
Assembly note:
2 panels: Perform assembly step four times
3 panels: Perform assembly step six times
4 panels: Perform assembly step eight times
5 panels: Perform assembly step ten times
The longer side of the h-profile points towards the inside.
17/b Top web panels (compensation profile)
Assembly note:
2 panels: Perform assembly step four times
3 panels: Perform assembly step six times
4 panels: Perform assembly step eight times
5 panels: Perform assembly step ten times
Position the compensation profiles centrally and secure (outside
profile view)
page 18
17/c 5-panel model, assembly preview of side (external view
– left front wall)
Note: The assembly preview shows the 5-panel model. The 2-, 3-
and 4-panel models differ only in terms of the number of side pan-
els; the assembly principle remains the same.
Profile view (h-profile / floor profiles)
Slide the bottom web panels together with the h-profiles into the
notch in the floor profile.
Profile view (compensation profile / rain gutter)
Insert the web panels together with the compensation profile into
the notch in the rain guttering profile at the top.
page 19
17/d 5-panel model, side assembly preview (external view –
left front wall)
Profile (double clip / side strut)
Assembly note:
2 panels: Perform assembly step four times
3 panels: Perform assembly step six times
4 panels: Perform assembly step eight times
5 panels: Perform assembly step ten times
Profile (single clip / corner profile)
Perform assembly step four times
page 20
18. Fitting the web panels to the roof (front
and rear wall)
18/a Bottom web panels
The longer side of the h-profile points towards the outside (profile
view).
GB
3