Faqs; Troubleshooting - BH iLynx Manuel

Masquer les pouces Voir aussi pour iLynx:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

EN
USER MANUAL

11. FAQs

What is the maximum speed of this bicycle?
It depends on the user. There is no maximum speed. However, at speeds over 25 km/h, the pedal assistance
provided by the motor is disabled. This restriction on assistance is a legal requirement for pedal-assist bicycles,
according to European regulation EN 15194:2017.
The NITRO and AWD models are an exception as they are not approved as pedal-assist bicycles. The maximum
assistance speed is limited to 45 km/h in NITRO models, which are approved as motorcycles.
Isn't a BH bicycle extremely heavy?
Not really, if you consider that the weight of BH bicycles is between 15 kg and 30 kg, depending on the model,
making them the lightest electric bicycles on the market. Pedal assistance means that a BH bike weighs 3-6 kg
more than a standard bicycle with the same characteristics, because of the battery and the motor.
Should I take any additional precautions when riding a BH bike instead of a standard bicycle?
No, but we recommend paying special attention when starting the BH, due to the additional thrust provided by
the motor. So we recommend starting it in 30%/ECO mode, with a short gear ratio (higher gears).
Do I have to stop every time that I want to activate pedal assistance?
No, pedal assistance can be activated while riding the bicycle, although it is not advisable because it may cause
a distraction. The only requirement to properly activate assistance is to stop pedalling for two seconds after
pressing the ON/OFF button,
thus enabling all of the elements of the electrical system to be properly activated.
Can I stand over the bicycle when I stop at traffic lights?
Yes. The motor will remain inactive as long as no pressure is being applied on the pedal. The greater the force
applied on the pedal, the greater the forward thrust on the bicycle. This is the result of the magnetic torque
sensor continuously reading the force applied on the pedal.
How often should I take the bicycle to a BH store for maintenance?
The other components require similar maintenance to the components of a standard bicycle, depending
on the frequency of use of the bicycle and how well it is looked after.
What should I do when I don't plan to use the bicycle for a long period of time?
We recommend charging it to 50% before storing it for a long time. We also recommend checking its charge
level every three months and keeping it above 50%.
Why is the range reduced when it is frosty or very cold?
This is normal; below -5ºC the performance of the battery is reduced. This does not cause any problems
or damage the battery, it simply means that it cannot be fully discharged, thus reducing the range of the bicycle.
Can I purchase additional batteries?
Yes, additional batteries are available at BH stores. If a longer range is required and it will not be possible
to charge the battery between two journeys, we recommend purchasing a second battery that is suitable
for the BH bicycle that you purchased.
Can I use the battery from my wife's electric bicycle?
Yes, provided that the battery is from a BH bicycle that is compatible with the model purchased by you. If the battery
is from another, non-compatible electric bicycle, it should not be used in the BH bike. This could damage
the assistance system beyond repair and would invalidate the warranty.
Should I use a helmet?
Whether or not a user has to wear a helmet depends on the law in each country, but we recommend using them
for safety reasons.
Should I have third-party liability insurance?
No, insurance is not compulsory, except for NITRO models.
Is there a minimum age required for using a BH bike?
No, any user can ride a BH bike, except for NITRO models.
42
ATOMX
ATOMX

12.TROUBLESHOOTING

Error
LED 4 LED 3 LED 2 LED 1
01
02
03
04
05
08
09
10
11
12
13
14
USER MANUAL
Description
Obervations
Check that the connection between the
System overcurrent
motor and the controller is OK. If not,
replace the controller.
System overcurrent
Replace the controller.
Check that the connection between the
TMM sensor and the controller is OK.
TMM sensor
Check if the TMM sensor's
output is exceeding the normal range;
it should be 0.1 V-3.5 V.
Check the motor's connector or the
Error in the motor
controller.
Check that the connection between
the motor and the controller is OK. If
the sensor inside the motor is broken,
Error in the motor's
replace the sensor or the motor with
sensor
a new one. Check that the connection
between the motor's cable and the
controller is OK. If not, replace the
controller.
Check the battery level or replace it with
Low battery
a new one.
Blocked motor
Motor stopped. Replace motor.
SIf there is faulty contact between the
System overcurrent
controller and the motor's connector,
replace it with a new one.
If the temperature exceeds the set
Overheating
value, the current will become gradually
weaker.
Protection against
The controller stops on entering
overheating
temperature protection mode.
Communication
Check the cable and the connector.
error
Take your foot off the pedal and turn it 
Pedal error
back on.
EN
43

Publicité

Table des Matières
loading

Table des Matières