Silverline 252190 Mode D'emploi page 7

r) All users of fall arrest gear must be medically fit for activities at height
and must wear appropriate personal protective equipment for the
environment, work carried out and tools used.
s) Carry out a risk assessment for every activity, and define a rescue plan
that can be safely and rapidly executed in case of emergency.
t) All product markings must remain intact and clearly legible for the
entire service life of this equipment.
u) Store the equipment with its dedicated service record and usage
instructions. Gear with uncertain service history must be removed from
service and destroyed.
v) Before using this equipment, ensure that it complies with local federal
regulations and other applicable safety standards.
w) Textile products including webbing and ropes MUST NOT be marked
using ink from marker pens or paint, as these substances may potentially
lead to chemical damage of the material.
x) Store in accordance with the manufacturer's instructions.
Product Familiarisation
1. Scaffold Hook
2. Karabiner
3. Rope Thimbles
4. Protective Sleeves (with safety labels)
5. Lanyard
Intended Use (Fig. I)
This lanyard is primarily used to connect to a suitable anchorage as part of a work
positioning or restraint system.
WARNING: Do not use the restraint positioning lanyard for fall arrest
purposes. Always use in conjunction with a compatible fall arrest system when
working at height.
Usage Limitations
WARNING: Do not use a work positioning or restraint belt if there is a risk of
becoming suspended or exposed to unintended tension by the belt.
WARNING: Fall arrest gear is designed to arrest a fall from height ONLY
ONCE! If subjected to an arrested fall, the gear must be withdrawn from service
and rendered unusable.
• Manual-locking or self-closing gates should only be used where the user
does not have to attach and remove the connector frequently, i.e. many times
during a working day
• This equipment is designed for use by one person with a combined total
weight no greater than 140kg, including clothing, tools, and other user-borne
objects
• Acidic, alkaline, or other environments with harsh substances may damage
the hardware of the karabiner. DO NOT expose the karabiner to corrosive
environments for prolonged periods of time. Organic substances and salt
water are particularly corrosive to metal parts
• Do not use in environments with temperatures lower than -40°C / -40°F or
greater than 80°C / 176°F
• Avoid contact with rough, abrasive surface, sharp edges, cutting tools etc.
• Equipment must be shielded when used near welding, metal cutting, or other
activities that produce large amounts of heat
• Use extreme CAUTION when working near energised electrical sources. Metal
hardware conducts electric current. Maintain a safe working distance (at least
3m from all electrical hazards
Restraint Positioning Lanyard
• A full body harness is the only acceptable body holding device that can be
used in a fall arrest system
• Never exceed a total sub-system length of 2m with an energy absorber,
including lanyard, terminations and connectors
• Never use a lanyard for fall arrest purposes without an Energy Absorber
• Always minimise the amount of slack in the lanyard near a fall hazard
• Always move to an area where there is no fall hazard to adjust the lanyard
length
Unpacking your Product
• Carefully unpack and inspect your product. Fully familiarise yourself with all
its features and functions
• Ensure all parts of the product are present and in good condition. If any parts
are missing or damaged, have such parts replaced before attempting to use
this product
Before Use
Pre-use checks
• An inspection must be carried out before every use. All parts of the gear must
be inspected in an area with appropriate light conditions
• Check correct function of Karabiner (2) and Scaffold Hook (1), and smooth
operation of their safety mechanisms
• Check the Lanyard (5), Rope Thimbles (3) and the Protective Sleeves (4) for
damage
Note: Refer to the 'Maintenance' section for further advice on inspection and
fault conditions.
• If the risk assessment shows that loading over an edge is possible, take
appropriate precautions to ensure safe use of the Lanyard
Clearance
Fall clearance (Fig II):
• Before use, it is essential to verify the clearance required beneath the user. This
clearance must be sufficient to prevent the user from hitting the ground or
another obstacle, in the event of a fall
Swing falls (Fig. III):
WARNING: The force of striking an object in a swing fall may cause serious
injury or death.
• Swing falls occur when the anchorage is not located directly above the point
where a fall occurs
• Minimise swing falls by working as close as possible to the anchorage
• DO NOT enter a situation where a swing fall could occur, if it is likely to result
in an injury
Note: The risk of swing falls significantly increases the clearance required when
using a self-retracting lifeline or another variable length connecting system.
WARNING: When connectors are poorly positioned, the attachment D-rings
could act as a lever on the gate of a karabiner and subsequently damage it when
sudden tension comes on to the rope. ALWAYS ensure connectors remain safely
positioned during use.
Anchorage requirements (Fig. IV)
• According to EN795 the minimum strength of any anchorage is 10kN
• Check anchorage for signs of deterioration
• Like all fall arrest gear, anchorages must be subjected to regular inspections
through a competent person. Inspect at least once every three months, and
record findings in a dedicated service record
• Check that the karabiner is the correct size for the anchorage to be used. If the
karabiner is too small, use an anchor sling to connect to the anchorage
silverlinetools.com
7