Equipment; Selecting Of The Installation Position; Installation And Adjustment Of The Reflector; Utilization - Vortice THERMOLOGIKA SOLEIL PLUS Notice D'emploi Et D'entretien

ENGLISH
close to or facing towards curtains, beds or other
objects or materials that are liable to burn easily;
always ensure that these objects are at a suitable
minimum distance, to avoid any risk of fire or heat
damage.
• Never use the appliance in combination with
programming devices, timers or other devices that
will switch it on and off automatically
• The appliance's safety guard has been specially
designed to prevent direct access to the heater
elements; this guard must be kept in position at all
times during operation.
• Specifications for the power supply must correspond
to the electrical data on data plate.

Equipment

Appliances TSP are supplied complete with:
- infrared lamp;
- cable mod H05SS-F 3x1.00 mm²;
- bracket and accessories for wall and ceiling
mounting (fig.2);
- stainless steel front grill;
Selecting of the installation
position
Never install the TS near to or facing towards
inflammable surfaces.
TS must be positioned at a distance of not less than 2
m from objects made of flammable materials, such as
cardboard or fabric, and from glass doors and
windows.
The lamp must never be mounted in such a way that it
points directly towards a wall or ceiling.
When the appliance is installed in environments (e.g.
workshops or car parks) containing flammable or
combustible substances (paints, solvents, etc.), TS
must be positioned at a distance of not less than 4 m
from the source of danger.
TS is not indicated for installation in extremely dusty
environments, in which the bulb might be damaged.
WARNING: never position TSP directly under a
power socket
Installation and adjustment of
the reflector
When mounting the appliance on a wall, it must be
positioned at a minimum distance of 20 cm from the
ceiling and 60 cm from the side walls (fig. 1); the height
from the floor may range.
When mounting the appliance on the ceiling it must be
positioned at a minimum distance of 60 cm. from the
side walls.
Attach the mounting plate to the lamp (fig.3) then fit the
plate to the bracket (fig.4). Next fit the wall mounting,
(fig.5 for wall mount, fig. 8 for ceiling mount) making
sure that you use the safety distance specified in the
instructions and installation booklet (figs. 6, 7, 9 and
10).
Adjust the TSP reflector so that it points in the direction
of the area to be heated. Maximum heating efficiency
is obtained with an inclination of 45°.
When mounting inside a bathroom, always respect the
minimum distances from showers and baths, and
ensure compliance with IPX5. Furthermore, the
commands to adjust the appliance and turn it on and
off must not be within reach of the shower or bath.
Within the safety limits outlined in this document, the
TSP unit can be installed either horizontally or
vertically using the appropriate fittings (optional
accessories) (fig. 3).

Utilization

To turn the appliance on and off, use the switch to
which the TSP has been connected during installation.
In the case of appliance connected to a Power
Regulator (optional accessory) the appliance is turned
on and off and the power delivered is regulated (30% -
100%) using the respective commands on the
Regulator.

Cleaning

From time to time, remove dust from the disk and bulb
using a clean brush or a jet of compressed air, so as to
guarantee that TSP provides maximum heating
efficiency at all times.
Electrical connections
Fig. A.For the different connection modes see figure A.
To connect the appliance in conformity with the current
regulations it is necessary to use one of the following
modes. (fig. A).
connects/disconnects the product from the power grid.
D1: wi-fi remote controller to predict at installation (cod.
21380).
D2: plug activable through wi-fi (cod. 21379).
D3: plug activable through wi-fi with temperature
sensor (cod. 21378).
The pull cord switch
7