Faq - Operating Anomalies (What To Do If - Harol VISION Mode D'emploi

Z
ANOMALOUS PERFORMANCE DURING THE PRODUCT TESTING
a - Blades set into motion but they stop substantially before, comparing to the required position
b - Blades set into motion, they stop and they set into motion in the opposite direction and then they
stop again
c - Blades do not move
d - Blades set into motion, they reach the maximum opening and they set into motion in the opposite
direction reaching the required position
e - Pergola version 02 with direct light: once reached the maximum opening, blades and motor go
substantially under stress
f - Pergola version 02 with indirect light: once reached the complete closure, blades and motor go
substantially under stress
g - Rain sensor doesn't start correctly the slats/blades
h - Some Led strips switch on with a completely different color comparing to the others or they do not
switch on
i - All spotlights or some of them do not switch on
l - The installed thermal magnetic circuit breaker and residual current device activated interrupting the
power supply
ANOMALOUS PERFORMANCE DURING THE USE OF THE PRODUCT
m - Blades set into motion, they stop and they set into motion in the opposite direction
n - Blades reach a 45° opening only
o - Once reached the complete closure or opening the motor makes noise
p - During the blade operation the motor makes noise
q - A part of the Led strip switches on with a different color or it does not switch on
r - One spotlight do not switch on
s - The functions available on the structure activate autonomously without commands from the remote
control
t - Some of/all the functions of the structure do not work and the control units emit an intermittent sound 11
u - Some channels of the remote control cannot be activated
OPERATIONS
1 - Check the kinematic motion of the blades by removing any obstacle to the operation
2 - If Spot light spotlights are present, check that their wiring, situated at the end of the blades, do not
prevent the blades from moving
3 - Check that all connections of the encoder circuit have been carried out and that the matching of the
wire colors has been respected
4 - Check the correct wall installation of the blades fixed profile/gutter
5 - Check that in the area there are no electromagnetic interferences
6 - If sensors are present, check that the performance of the blades is not the consequence of the usual
operation of the sensors
7 - Carry out the setting of the limit switch through remote control excluding/disconnecting temporarily
the wind and rain sensors, if present
8 - Carry out the setting of the limit switch
9 - The channel restriction function has been activated, deactivate it
10 - The remote control is equipped with batteries, which are charged
11 - Check that the electrical system connections are correct and intact
12 - Check that the electrical system of the structure is complete and that all its components are powered
13 - Check that the mains supply is present
14 - The motor/ the Led strip/ the spotlight is damaged and must be replaced
15 - Check the link; Install the "L" shaped steel bracket to separate the sensor from the structure
16 - Contact Pratic Customer service, providing the order reference of the structure

FAQ - Operating anomalies (what to do if...)

PAG. 74 Lamellendak VISION - installatiehandleiding Rev. 11/21
ORDER OF THE OPERATIONS
1 2 3 5 6 7 16
→ → → → → →
1 2 3 5 6 7 16
→ → → → → →
10 1 2 3 5 6 7
→ → → → → → →
3 5 7 16
→ → →
4 7 16
→ →
4 7 16
→ →
15 16
→
11 16
→
11 16
→
11 12 13 16
→ → →
ORDER OF THE OPERATIONS
1 2 16
→ →
6 16
→
14 16
→
14 16
→
14 16
→
11 14 16
→ →
6 5 16
→ →
16
→
9
IMPORTANT: the test for the correct
functioning of the blades must be
carried out only after the installation
has been completed, before ap-
plying the last finishing crankcases.
If the test is carried out during
previous steps of the structure as-
sembly procedure it could be dan-
gerous, could create anomalous
performance of the electronic devi-
ces and could require reconfigura-
tion procedures.
A F S
T A N
R E
D S
M O
B E D
T E
T É L IE N
C O
É C IN G
N T
O M
F U R O
M A
N K
L
S E N N D
E
D E
R
Gebruiksinstructies
Instructions manual
Manual d'utilisation
Bedienungsanleitung
Documentatie van de fabrikant
Manufacturer's documentation
Documetation du fabricant
Herstellerdokumentation
16