Bosch GGS 5000 Professional Notice Originale page 8

OBJ_BUCH-1420-007.book Page 8 Wednesday, July 27, 2016 3:16 PM
8 | English
Technical Data
Straight grinder
Article number
Rated power input
Rated speed
Collet chuck diameter, max.
Spindle collar dia.
Thickness of grinding wheels, max.
Grinding tool diameter, max.
Weight according to EPTA-Procedure 01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-23.
Typically the A-weighted noise levels of the product are
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertain-
h
ty K determined according to EN 60745-2-23.
Grinding surfaces (roughing):
a
h
K
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signif-
icantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Only for EC countries:
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards: EN 60745-1,
EN 60745-2-23, EN 50581.
1 609 92A 2F2 | (27.7.16)
GGS 5000
3 601 B23 0..
W 500
-1
min 33000
mm 8
mm 43.5
mm 30
mm 25
kg 1.0
/II
GGS 5000
3 601 B23 0..
dB(A) 80
dB(A) 91
dB 3
2
m/s 7.0
2
m/s 1.5
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ETM9,
70538 Stuttgart, GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch Power Tools GmbH
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
Assembly
 Before any work on the machine itself, pull the mains
plug.
 Only use grinding points with a matching shank diame-
ter. A grinding point/accessory with a shank diameter that
does not fit the tool holder (see "Technical Data"), can not
be clamped properly and will damage the collet chuck.
 The application tool must be clamped at least 10 mm.
The inner shank dimension L
0
maximum permitted speed of the application tool from the
specifications provided by manufacturer of the application
tool. It must not be less than the maximum speed of the
power tool.
GGS 5000 L
3 601 B24 1..
500
33000
8
41
30
25
1.4
/II
GGS 5000 L
3 601 B24 1..
81
92
3
18.5
1.5
can be used to calculate the
Bosch Power Tools