Robert Juliat ARAMIS+ Dossier Technique page 6

Please read carefully all the instructions before operating the appliance.
GENERAL INSTRUCTIONS
1. Not for residential use.
2. Only qualified technicians are permitted to service these
fixtures.
3. In addition to the instructions indicated on this page, you must
adhere to the relevant health and safety requirements of the
appropriate EU Directives.
4. This fixture is in compliance with section 17: Lighting appliance
for theatre stages, television, cinema and photograph studios.
Standards NF EN 60598-1 and NF EN 60598-2-17.
5. This fixture is rated as IP20, and is for indoor use only.
FIXTURE
6. Warning: high voltage ignition. Disconnect from the mains
before any servicing.
7. Make sure the fixture is correctly mounted on an appropriate
support.
8. The protection screens, lenses or U.V. filters must be replaced
if there is any visual damage which might reduce their
performance, for example, by cracks or deep scratches.
9. When hung or flown the fixture must be secured by another
hanging accessory (such as a safety cable or bond) that is of
suitable length. The safety bond or cable must be securely
attached at the back of the fixture. It must be as short as possible
or rolled up as necessary to ensure the fixture does not travel any
distance should it be dislodged.
10. Movable accessories (barn doors, HMI shutters, spill rings etc.)
must also be secured with a suitable safety cable or bond at
the front of the fixture. Take into account the weight of both the
fixture and the accessories when choosing the strength of the
attachment point and the safety cable or bond.
11. Do not open the lighting fixture when the lamp is on.
12. Both the lamp and lamp housing heat up when powered. Wait
until the fixture is cold before servicing.
13. Do not tamper with the design of the fixture nor any of its safety
features.
14. Tighten the electrical mains cable connections regularly. Replace
mains cable with an identical one if damaged.
15. Use only with correct power supply.
Ventilation
16. Keep well away from flammable material.
17. Do not use outside. Do not cover. Do not permit the fixture to
get wet.
18. To avoid overheating, do not obstruct air vents.
19. If the fixture has fans, make sure they are working correctly.
If fans are not working, turn the fixture off immediately and
service as necessary.
robert juliat
32 Rue de Beaumont F 60530 Fresnoy-en-Thelle phone: +33 (0)3.44.26.51.89 - fax: +33 (0)3.44.26.90.79 - www.robertjuliat.fr
TECHNICAL FILE
USER'S INSTRUCTIONS
2500W HMI FOLLOWSPOT
Lamp
Danger
The discharge lamp used emits short-wave ultraviolet
radiation which is harmful to skin and eyes.
20. Use only fully enclosed in the fixture.
21. Never look at the lamp directly.
22. Warning : U.V. rays : Protect your eyes.
23. Check that the lamp voltage corresponds to the mains voltage
used. Do not use a lamp with power that is an incorrect type
or voltage to the one that is indicated on the lamp housing or
packaging.
24. The lamp must be replaced if it has been damaged or deformed
by the heat.
25. Use only when bulb is in place.
Cleaning
26. Do not touch the lamp or the mirror with your fingers.
27. To clean the optical parts, use a soft cloth in combination with
distilled water or isopropyl alcohol recommended for coated
optics. Do not use any cleaning product that contains solvents
or abrasives, as these can cause surface damage. Dry with a soft
lint-free cloth.
28. Regularly remove dust from the mirror with a soft and clean lint-
free cloth.
29. If the fixture has filters they must be cleaned frequently.
POWER SUPPLY
30. Disconnect from the mains before any servicing.
31. Mains connection only. Do not connect to an "electronic output"
(dimmer, static relay...).
32. Do not use outside. Do not cover.
33. The power supply has circuit breakers, which should always be
kept accessible.
34. There is no maximum distance between the lighting unit and the
power supply.
35. Check the mains voltage.
PLEASE NOTE
These products have been built to conform to European standards
relating to professional lighting equipment. Any modification made
to our products will void the manufacturers' warranty
+
1013 /
B, BS, M & BSM
Section A - 1